Skip to content
Omnikalc

Ćuk converter calculator

Enter the input voltage, the duty cycle, the load current, the inductors, the capacitors and the frequency to get the output voltage and the ripples in both inductors and capacitors.

Updated on
Your inputs
V

Value out of range

%

Value out of range

A

Value out of range

µH

Value out of range

µH

Value out of range

µF

Value out of range

µF

Value out of range

kHz

Value out of range

Results

Output voltage (inverted)

-8.00 V

Average input current

0.667 A

Peak switch current

2.15 A

Average voltage across C1 (Vin + |Vout|)
20.00 V
Ripple current in L1
0.480 A
Ripple current in L2
0.480 A
Ripple voltage across C1
0.400 V
Output voltage ripple
12.8 mV
Switch voltage stress (Vin + |Vout|)
20.00 V

The Ćuk converter calculator gives the output voltage, the input current, the voltage across the coupling capacitor, the ripple currents in both inductors, the ripple voltages, the peak switch current and the switch voltage stress, for an ideal converter in continuous conduction.

How the calculation works

  • Enter the input voltage, the duty cycle and the load current.
  • Enter the inductors L1 and L2, the capacitors C1 and C2 and the switching frequency.
  • Read the output voltage, the ripples and the stresses on the switch.

Example

With an input of 12 V and a duty cycle of 40 %, the output is -8.00 V and the input current 0.667 A for a load of 1 A. The coupling capacitor sees 20.00 V with a ripple of 0.400 V. The inductor ripples are 0.480 A and 0.480 A, the output ripple is 12.8 mV and the switch must handle 2.15 A and 20.00 V.

Why it matters

The calculator helps electronics students, power supply designers and hobbyists who need a negative rail from a positive supply, a low-noise inverting converter for audio or sensors, or a quick check of the inductor, capacitor and switch ratings of a Ćuk stage.

Good to know

The calculation assumes an ideal converter with continuous inductor currents, so the real output voltage is a little lower because of the losses in the switch, the diode and the resistances. Check that the inductor currents stay positive over the cycle, which is true when the ripple is below twice the average current. The coupling capacitor must be rated for the ripple current, and the output polarity is negative with respect to the input ground. Add margin to the ratings of the components for transients and tolerance.

The inverting buck-boost converter calculator gives a simpler topology with the same ratio, the buck converter calculator steps down, the boost converter calculator steps up and the flyback converter calculator adds isolation.

Frequently asked questions

What is a Ćuk converter?

The Ćuk converter, invented by Slobodan Ćuk, is a DC-DC converter that produces an output voltage of opposite polarity to the input, which can be higher or lower in magnitude. It has an inductor at the input and one at the output, so both currents are continuous with low ripple, and it transfers energy through a coupling capacitor.

What is the voltage conversion ratio?

In continuous conduction, the output voltage is Vo = −Vin × D / (1 − D), where D is the duty cycle. A duty cycle below 50 percent steps the voltage down, and above 50 percent it steps it up. The input current is Iin = Io × D / (1 − D) for an ideal converter without losses.

How does it differ from the inverting buck-boost converter?

Both give the same ideal voltage ratio. The buck-boost has a pulsating input and output current, while the Ćuk has inductors on both sides, so the currents are smooth. The Ćuk needs a coupling capacitor that carries the full transferred power, which must be rated for the ripple current, and two inductors that can be wound on a single core.

How do I choose the components?

The ripple currents in the inductors are Vin × D / (L × f), and a typical target is 20 to 40 percent of the average current. The coupling capacitor should have a low ESR and a ripple rating above the load current. The switch carries the sum of both inductor currents, and the diode and switch see a voltage of Vin + |Vo|.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.