Skip to content
Omnikalc

Goodman fatigue calculator: does your part survive a stress that never stops cycling?

Enter the endurance limit, the strengths and the alternating and mean stresses to get the Goodman, Gerber and yield safety factors.

Updated on
Your inputs
ksi

Value out of range

ksi

Value out of range

ksi

Value out of range

ksi

Value out of range

ksi

Value out of range

Results

Goodman safety factor

1.37

Thin margin for a fatigue-loaded part
Gerber safety factor
1.70
Yield safety factor
1.88
Largest alternating stress allowed at this mean stress (Goodman)
18.8 ksi

Most real parts see a steady stress with a cycling stress on top, and fatigue life depends on both. The Goodman fatigue calculator takes the endurance limit, the tensile strength, the yield strength, the alternating stress and the mean stress, and gives the Goodman safety factor, the Gerber safety factor, the yield safety factor and the largest alternating stress allowed at the given mean stress.

How the calculation works

  • Enter the corrected endurance limit, the ultimate tensile strength and the yield strength of the material.
  • Enter the alternating stress σa, which is half the stress range, and the mean stress σm.
  • The Goodman safety factor is n = 1 / (σa/Se + σm/Sut). The Gerber parabola is less conservative, and the yield factor is Sy / (σa + σm).
  • The lowest of the three factors governs. A fatigue factor below 1 means that failure is predicted, and a factor of 1.5 or more leaves a comfortable margin.

Example

A steel has Se = 25 ksi, Sut = 80 ksi and Sy = 60 ksi, and a point of the part sees σa = 12 ksi and σm = 20 ksi. The Goodman factor is 1 / (12/25 + 20/80) = 1 / 0.73 = 1.37. The Gerber factor is 1.70 and the yield factor is 60 / 32 = 1.88. At a mean stress of 20 ksi, the alternating stress could rise to 25 × (1 − 20/80) = 18.8 ksi before reaching the Goodman line.

Why it matters

The Goodman line is the most used fatigue criterion in machine design, for shafts, springs, bolts, brackets and connecting rods. A quick factor shows whether a design has a margin, how much a lower mean stress, such as a lower preload, helps, and whether a larger endurance limit from a better finish would change the result.

Good to know

The criteria assume a fully known stress state, a uniform loading with constant amplitude and a ductile steel. Variable-amplitude loads need a damage rule such as Miner’s rule. Stress concentrations must be included in the stresses, and compressive mean stresses are not beneficial in the Goodman line as used here. For safety-critical parts, use test data and a full analysis.

The pressure vessel stress calculator finds wall stresses, the shaft torsion calculator checks twisted shafts, the compression spring calculator sizes springs, and the bolt torque calculator sets bolt preload.

Frequently asked questions

What is a Goodman diagram?

It is a plot of the alternating stress against the mean stress, with a straight line from the endurance limit on the vertical axis to the tensile strength on the horizontal axis. Points under the line are predicted to survive an unlimited number of cycles, and points above it are not. It accounts for the fact that a tensile mean stress lowers the allowable alternating stress.

What is the difference between Goodman and Gerber?

The Goodman line is straight and conservative, and it is the usual choice for design. The Gerber curve is a parabola that fits test data for ductile metals better, so it gives a higher factor. The ASME elliptic and the Soderberg lines are other options, and Soderberg, which uses the yield strength, is the most conservative.

What are the alternating and mean stresses?

For a stress that cycles between a maximum and a minimum, the alternating stress is half the difference and the mean stress is the average. A shaft in rotating bending has a mean stress of zero. A bolt with a preload has a large mean stress and a small alternating one. The two together set the position on the diagram.

Why check the yield factor too?

The Goodman line extends to the tensile strength, but a part that yields on the first cycle is useless even if it would not fatigue. The yield check, with the maximum stress σa + σm, makes sure there is no yielding. Where the yield factor is lower than the fatigue factor, yielding governs the design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.