Skip to content
Omnikalc

Basquin fatigue life calculator: how many cycles will it take at your stress amplitude?

Enter the stress amplitude and the Basquin constants of the material to get the cycles to failure and the time to failure at a given frequency.

Updated on
Your inputs
ksi

Value out of range

ksi

Value out of range

Value out of range

Hz

Value out of range

Results

Cycles to failure N

1,194,250

High-cycle fatigue: a long life
Reversals to failure 2N
2,388,500
Time to failure at the loading frequency
33:10:25
Stress amplitude as a share of σf′
26.7 %

Parts that carry a repeated load fail after a certain number of cycles, even when the stress is far below the strength of the material. Basquin’s law gives the number of cycles for a given stress amplitude. The Basquin fatigue life calculator takes the stress amplitude, the fatigue strength coefficient, the fatigue strength exponent and the loading frequency, and gives the cycles to failure, the reversals, the time to failure and the stress as a share of σf′.

How the calculation works

  • Enter the stress amplitude σa of the load cycle, and the two Basquin constants of the material: the fatigue strength coefficient σf′ and the fatigue strength exponent b, which is negative.
  • The calculator applies Basquin’s law: σa = σf′ × (2N)^b, where 2N is the number of reversals (half cycles) to failure.
  • Solving for the life gives N = 0.5 × (σa / σf′)^(1/b) cycles to failure.
  • With the loading frequency, it also gives the time to failure. For stress levels low enough to give more than 100 trillion cycles, the life is capped.

Example

A steel has σf′ = 150 ksi and b = −0.09. It is loaded with a stress amplitude of 40 ksi. The ratio σa / σf′ is 0.267, so the number of reversals is 0.267^(1 / −0.09) = 2.39 million, and the life is 1.19 million cycles. At 10 Hz, this is 119,000 s, or about 33 hours.

Why it matters

Fatigue causes most failures of moving machine parts, from shafts and springs to bridges and aircraft. Basquin’s law is the starting point of stress-life design: it turns the stress amplitude into a life, and it shows how steeply the life drops when the stress rises. A small increase in the stress can cut the life by a factor of ten.

Good to know

The law is for fully reversed loading of smooth parts, with a mean stress of zero, and it ignores surface finish, size, stress concentrations, corrosion and temperature, which reduce the life. For a mean stress, use a correction such as Goodman. The scatter in fatigue is large, and a factor of 3 to 10 in life is normal. Use the result for a first design estimate and not as proof of safety.

The Goodman fatigue factor calculator corrects for mean stress, the Paris law calculator covers crack growth, the endurance limit calculator gives the stress below which life is practically infinite, and the Hertz contact stress calculator covers contact fatigue.

Frequently asked questions

What is Basquin’s law?

It is the equation of the high-cycle part of the S–N curve, which says that the stress amplitude falls as a power of the number of reversals to failure: σa = σf′ (2N)^b. On a log–log plot it is a straight line with a slope b, usually between −0.05 and −0.12 for metals. It was proposed by Basquin in 1910.

What are typical values of σf′ and b?

The fatigue strength coefficient σf′ is close to the true fracture strength of the material, so it is a bit above the tensile strength, and b is typically −0.06 to −0.12. For steels, a common estimate is σf′ ≈ σu + 50 ksi (345 MPa), where σu is the ultimate tensile strength, and for aluminium alloys b is about −0.1. These constants are best taken from test data for the material and the surface condition.

What about the endurance limit?

Basquin’s law keeps falling with no end, while many steels show a knee at about one million cycles below which they appear to last indefinitely. When the stress amplitude is below the endurance limit, use the endurance limit and not the straight line. The calculator shows the result of the line alone and warns when the life is very long.

Does it work for low-cycle fatigue?

No. At high strain, when the life is under about 10,000 cycles, the plastic strain dominates and the Coffin–Manson relation applies. The strain-life equation of Morrow adds the two relations. Basquin is the elastic part, and the calculator labels results in the low-cycle zone with a warning.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.