Skip to content
Omnikalc

OD600 cell density calculator: how many cells does your culture hold?

Enter the OD600 reading, the dilution and the cells per OD unit to get the cell density, the total cells and the volume to transfer for a new culture.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

mL

Value out of range

Value out of range

mL

Value out of range

Results

OD600 of the undiluted culture

1.900

The reading is in the range where OD is roughly proportional to cell density
Cell density (cells per mL)
1,520,000,000
Total cells in the culture
76,000,000,000
Volume of culture to transfer for the new culture
2.632 mL

Optical density is the fastest way to estimate how much a microbial culture has grown. The OD600 cell density calculator takes the reading, the dilution factor and the cells per OD unit, and gives the OD of the undiluted culture, the cell density, the total cells and the volume to transfer to start a new culture at a chosen OD.

How the calculation works

  • Measure the OD600 of your culture, diluting it if the reading would otherwise be high, and enter the reading with the dilution factor.
  • Enter the cells per mL for one OD600 unit for your organism and instrument. A common value for E. coli is about 8 × 10⁸, and for yeast about 1.5 × 10⁷.
  • The OD of the undiluted culture is the reading × the dilution factor. Cell density = OD × cells per mL per OD unit.
  • To start a new culture at a target OD and a final volume, transfer target OD × final volume ÷ OD of the culture.

Example

A sample diluted 1 to 5 reads 0.38, so the culture has an OD600 of 1.9 and, at 8 × 10⁸ cells per mL per OD unit, a density of 1.52 × 10⁹ cells/mL. A 50 mL culture holds 7.6 × 10¹⁰ cells. To start 100 mL at an OD of 0.05, transfer 0.05 × 100 ÷ 1.9 = 2.632 mL.

Why it matters

Molecular biology and fermentation labs seed cultures, induce expression and harvest cells at a specific OD. A reliable conversion avoids over- or under-inoculating and saves time on repeated measurements.

Good to know

The conversion from OD to cells is approximate, and it changes with the strain, the cell size, the growth phase and the spectrophotometer. Calibrate with your own system for accurate work, and keep readings within the linear range of the instrument.

The cell doubling time calculator predicts how long growth takes, and the serial dilution calculator plans the dilutions needed for a reading.

Frequently asked questions

What does OD600 measure?

It is the optical density of a culture at a wavelength of 600 nm. Cells scatter light, so a denser culture lets less light through and gives a higher reading. It is a quick, non-destructive way to follow bacterial or yeast growth.

Why dilute the sample before reading?

Spectrophotometers are only roughly linear up to an OD of about 0.4 to 0.6. Above this, light that was scattered is measured again, and the reading underestimates the real density. Diluting the sample brings it back into the linear range, and the dilution factor restores the true value.

How do I find the cells per OD unit for my strain?

The value depends on the organism, the strain, the growth phase and the instrument. Calibrate it by plating dilutions of a culture at a known OD and counting colonies, or by counting with a hemocytometer. The numbers used here are typical starting values.

How is the transfer volume computed?

The new culture needs a total OD of target × final volume. The stock culture supplies OD units equal to its OD times the volume taken, so the volume is the target OD × final volume ÷ the OD of the culture.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.