Skip to content
Omnikalc

Solar cell fill factor calculator: how good is the current-voltage curve?

Enter Voc, Jsc, Vmp, Jmp and the light power to get the fill factor, the efficiency and the ideal fill factor for the cell.

Updated on
Your inputs
V

Value out of range

mA/cm²

Value out of range

V

Value out of range

mA/cm²

Value out of range

mW/cm²

Value out of range

Results

Fill factor

79.4 %

High fill factor: low resistance losses
Power conversion efficiency
20.5 %
Maximum power density
20.52 mW/cm²
Ideal fill factor for this Voc (no resistance losses)
84.3 %
Fill factor as a share of the ideal
94.2 %

The shape of a solar cell’s current-voltage curve decides how much of its voltage and current becomes useful power. The solar cell fill factor calculator takes the open-circuit voltage, the short-circuit current density, the voltage and current density at the maximum power point and the light power, and gives the fill factor, the efficiency, the maximum power density, the ideal fill factor for that voltage and the share of the ideal reached.

How the calculation works

  • Enter the cell’s open-circuit voltage (Voc) and short-circuit current density (Jsc), taken from the current-voltage curve.
  • Enter the voltage and current density at the maximum power point (Vmp and Jmp), where the product of the two is the highest.
  • Enter the light power that fell on the cell. The standard test condition is 100 mW/cm², one sun.
  • The fill factor is (Vmp × Jmp) ÷ (Voc × Jsc), the share of the box under the curve that the maximum power rectangle fills. The efficiency is the maximum power divided by the light power.

Example

A silicon cell has Voc 0.68 V, Jsc 38 mA/cm², Vmp 0.57 V and Jmp 36 mA/cm² under 100 mW/cm². The fill factor is (0.57 × 36) ÷ (0.68 × 38) = 20.52 ÷ 25.84 = 79.4 %. The maximum power density is 20.52 mW/cm², so the efficiency is 20.5 %. For a Voc of 0.68 V, an ideal cell without resistance losses would have a fill factor of 84.3 %, so this cell reaches 94.2 % of the ideal.

Why it matters

A low fill factor reveals resistive losses or leakage that are not visible from the voltage and current alone, so it is a quick diagnostic for cell quality. Comparing it with the ideal value shows how much room is left to improve, which is useful for researchers, students and anyone reading a solar cell data sheet.

Good to know

The efficiency here assumes the standard test light of 100 mW/cm², the AM1.5 spectrum, and a temperature of 25 °C. Results under other conditions differ. The ideal fill factor uses a simple approximation with an ideality factor of 1. Measurements should come from a calibrated solar simulator.

The Shockley diode calculator gives the behaviour of the diode inside a solar cell, the photon energy calculator relates light colour to energy, the solar panels calculator estimates a home system’s payback, and the thin-film interference calculator covers coatings on cells.

Frequently asked questions

What is the fill factor of a solar cell?

It is the ratio of the maximum power of the cell to the product of its open-circuit voltage and short-circuit current. It tells you how square the current-voltage curve is. A perfectly square curve would have a fill factor of 100 percent. Real cells reach 70 to 85 percent.

Why is it never 100 percent?

The diode behaviour of the cell means the current drops gradually near the open-circuit voltage, not suddenly. On top of that, series resistance in the contacts and metal, and shunt leakage across the cell, round the corner of the curve further. The ideal value for a given Voc includes only the diode shape.

What affects the efficiency?

Efficiency is the fill factor times Voc times Jsc divided by the light power. A good cell needs a high voltage, a high current and a high fill factor. Voc depends on the material, Jsc on how much light is absorbed and collected, and the fill factor on resistance and recombination.

What is the ideal fill factor formula?

The calculator uses the Green approximation, FF₀ = (voc − ln(voc + 0.72)) ÷ (voc + 1), where voc is the open-circuit voltage divided by the thermal voltage kT/q, about 25.7 mV at 25 °C. It is valid for an ideal diode with an ideality factor of 1, and for voc above about 10.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.