Skip to content
Omnikalc

PCB propagation delay calculator: how long does a signal take on your trace?

Choose microstrip or stripline, enter the permittivity, the trace length, the mismatch and the rise time to get the delay, the skew, the signal speed and the critical length.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

ns

Value out of range

Results

Delay of the trace

560.0 ps

Propagation delay per inch
140.0 ps/in
Delay of the length mismatch (skew)
35.0 ps
Signal speed as a share of the speed of light
60.5 %
Critical length for this rise time
1.79 in
Length divided by the critical length
2.24
The trace is longer than the critical length: treat it as a transmission line

The speed of a signal on a printed circuit board depends on the board material and on where the trace runs. The PCB propagation delay calculator takes the trace type, the relative permittivity, the trace length, a length mismatch and the rise time of the signal and gives the propagation delay per inch, the delay of the trace, the skew of the mismatch, the signal speed and the critical length.

How the calculation works

  • Propagation delay per inch: for a microstrip, 85 × √(0.475 × εr + 0.67) picoseconds, and for a stripline, 85 × √εr picoseconds (the IPC-2141 formulas).
  • Delay of the trace = delay per inch × the length in inches. Skew is the same formula for the length mismatch between two traces, for instance the two lines of a differential pair.
  • Signal speed = 1 inch ÷ the delay per inch, shown as a share of the speed of light, 299 792 458 m/s.
  • Critical length = rise time ÷ (2 × delay per unit length). Beyond it the reflections arrive within the rise time and the trace must be treated as a transmission line.
  • The last result is the trace length divided by the critical length. Above 1, think about termination and impedance control.

Example

A 4 in microstrip on FR-4 with εr = 4.3 has a delay of 85 × √(0.475 × 4.3 + 0.67) = 140 ps/in, so the trace has a delay of 560 ps. A mismatch of 0.25 in gives 35 ps of skew. The signal travels at 60.5 percent of the speed of light. For a rise time of 0.5 ns the critical length is 500 ÷ (2 × 140) = 1.79 in, so the 4 in trace is 2.24 times the critical length.

Why it matters

High-speed designs depend on timing. Matching the lengths of a bus, tuning a differential pair or checking whether a trace needs termination all start from the delay per unit length. The calculator gives the figures quickly, so you can set length-matching limits before you route.

Good to know

The formulas of IPC-2141 are approximations for typical geometries, and a field solver gives more accurate figures for a given stack-up. The permittivity of FR-4 changes with frequency and the resin content of the laminate, and the solder mask changes the effective value on a microstrip. Vias and connectors add delay that is not counted here.

The PCB trace width calculator sizes a trace for its current, and the wire resistance calculator gives the resistance of a conductor.

Frequently asked questions

Why is a signal slower in a PCB than in air?

The signal travels in the electromagnetic field around the trace, which is partly inside the board material. A higher permittivity slows the wave by the factor of the square root of the effective permittivity. On FR-4 the speed is around 50 to 60 percent of the speed of light.

What is the difference between microstrip and stripline?

A microstrip is on an outer layer, with air above and the board below, so its effective permittivity is lower and its signals are faster. A stripline is buried between two planes, completely surrounded by the board material, so it is slower and has the same delay on every inner layer.

When must I match trace lengths?

When several signals must arrive together, such as a memory bus, the two lines of a differential pair or a clock and its data. The permitted skew is a fraction of the bit time. At 1 Gb/s a bit lasts 1 ns, and 35 ps of skew is already 3.5 percent of it.

What is the critical length?

It is the trace length beyond which reflections matter. A common rule is that a trace is a transmission line when its one-way delay exceeds half the rise time, which gives rise time ÷ (2 × delay per unit length). Other rules use one sixth or one tenth of the rise time, so treat the result as a guide.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.