Skip to content
Omnikalc

Spherical and cylindrical capacitor calculator

Choose concentric spheres or coaxial cylinders, enter the radii, the dielectric and the voltage to get the capacitance, the charge and the energy.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

m

Value out of range

Value out of range

V

Value out of range

Results

Capacitance

11.13 pF

Charge
11.13 nC
Stored energy
5.56 µJ
Field at the inner conductor
40.0 kV/m

The spherical and cylindrical capacitor calculator gives the capacitance, the charge, the stored energy and the field at the inner conductor for concentric spheres or coaxial cylinders.

How the calculation works

  • Choose the geometry: concentric spheres or coaxial cylinders.
  • Enter the inner and outer radius, the length of the cylinders, the relative permittivity of the dielectric and the voltage.
  • The calculator gives the capacitance, then the charge Q = C × V, the energy ½ × C × V² and the field where it is highest.

Example

Two concentric spheres of 50 mm and 100 mm radius, with air between them, have a capacitance of 11.13 pF. Charged at 1000 V, they hold 11.13 nC and 5.56 µJ, and the field at the inner sphere is 40.0 kV/m, well below the breakdown field of air.

Why it matters

The calculator helps physics students who work through the classic capacitor geometries, engineers who design high-voltage electrodes, probes and coaxial lines, and anyone who wants to compare the capacitance of a sphere with a plate or a cable.

Good to know

The capacitance depends only on the geometry and the dielectric, not on the voltage. Doubling the gap between the spheres does not halve the capacitance, because the field falls with the square of the distance. For the cylinders the ratio b / a matters more than the absolute size. The field at the inner radius sets the voltage limit: a small inner conductor concentrates the field, so a fine wire in a large tube breaks down at a lower voltage than a thick rod. The formulas hold for a uniform dielectric and a gap small compared with the length. For a real capacitor add the stray capacitance of the leads, and derate the voltage rating by a safety factor of two or more.

The capacitors calculator combines capacitors in series and parallel, the Gauss’s law calculator gives the field of a charge distribution, the coax electrical length calculator relates the cable to its propagation and the characteristic impedance calculator gives the impedance of a line.

Frequently asked questions

What is the capacitance of two concentric spheres?

For an inner sphere of radius a and an outer shell of radius b separated by a dielectric of relative permittivity εr, the capacitance is C = 4 × π × ε0 × εr × a × b / (b − a). When b is much larger than a, this tends to 4 × π × ε0 × εr × a, the capacitance of an isolated sphere. A sphere of 10 cm radius in air is about 11 pF.

What is the capacitance of coaxial cylinders?

For coaxial cylinders of length L, with an inner radius a and an outer radius b, the capacitance is C = 2 × π × ε0 × εr × L / ln(b / a). The result applies when L is much larger than b, so that the ends can be ignored. This is the model of a coaxial cable, which has a capacitance per metre of about 50 to 100 pF.

Where is the field strongest?

The field is highest at the surface of the inner conductor, since the same flux crosses a smaller area there. A sharp or small inner conductor therefore sets the breakdown voltage of the capacitor. Air breaks down near 3 000 kV/m, and a dielectric such as polyethylene resists several times more, so the voltage limit comes from the field at the inner radius.

What does the calculator leave out?

The calculator assumes a uniform dielectric that fills the gap and ignores edge effects, a finite length for the spheres and the stray capacitance to the surroundings. It does not model a dielectric with losses or a voltage-dependent permittivity. For a real component, use the data sheet value and use the calculation to compare designs.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.