Skip to content
Omnikalc

Transformation efficiency calculator: how good are your competent cells?

Enter the colonies on the plate, the plated and total volumes and the amount of control DNA to get the transformation efficiency in colony-forming units per microgram of DNA.

Updated on
Your inputs

Value out of range

µL

Value out of range

µL

Value out of range

pg

Value out of range

Value out of range

Results

Transformation efficiency

250,000,000 cfu/µg

High Good for ligations and small libraries.
Total transformants in the culture
2,500 cfu
Efficiency as a power of ten
8.40 log₁₀ cfu/µg
Efficiency per nanogram of DNA
250,000 cfu/ng
Share of the culture on the plate
10.0%
Colonies on the plate
250
Countable The plate is in the reliable counting range of 30 to 300 colonies.

Transformation efficiency tells you how well competent bacteria take up DNA. It is the number of colonies you would get per microgram of plasmid, and it is the number to check when you make or buy competent cells. This calculator corrects the colonies on the plate for the part of the culture that was plated and for any dilution, and divides by the amount of DNA used.

How the calculation works

  • Total transformants = colonies × (total volume ÷ plated volume) × dilution factor
  • DNA in micrograms = DNA in picograms ÷ 1,000,000
  • Efficiency = total transformants ÷ DNA in micrograms, in cfu/µg

Example

You transform cells with 10 pg of a control plasmid, add recovery medium to reach 1000 µL and plate 100 µL. The plate shows 250 colonies. Only 10.0 % of the culture was plated, so the culture holds 2,500 transformants. Dividing by 0.00001 µg of DNA gives an efficiency of 250,000,000 cfu/µg, or 8.40 on a log scale. For chemically competent cells, this is a high efficiency.

Why it matters

A low efficiency means few clones from a ligation, which can ruin a cloning experiment. A high efficiency is needed for libraries, where every clone counts. The measure also lets you compare batches of competent cells and protocols, and decide whether to remake them. Always use a small amount of DNA, well below saturation, because efficiency falls when too much DNA is used.

Good to know

Count plates with 30 to 300 colonies, and dilute if you have more. Use the amount of DNA that went into the transformation, not what is on the plate. The result is only valid for the strain, the plasmid size and the method you used: large plasmids transform less well, and ligation mixes give lower numbers than supercoiled plasmid. Typical values are 10⁶ to 10⁸ cfu/µg for homemade chemical cells, 10⁸ to 10⁹ for commercial high-efficiency cells and 10⁹ to 10¹⁰ for electroporation. Include a no-DNA control to check for contamination.

In practice

Run a control transformation each time you make a new batch of cells, and write the result on the tube. Do the same with each new lot of cells. This tool is a calculator for lab routine, not a substitute for your protocol.

Frequently asked questions

What is a good transformation efficiency?

For cloning, 10⁸ cfu/µg or more is good. Homemade chemical cells often reach 10⁶ to 10⁷, and electrocompetent cells 10⁹ or more.

Why does the volume plated matter?

You only plate a fraction of the recovered culture, so the colonies on the plate must be scaled up by total volume divided by plated volume to count all the transformants.

Which DNA amount should I use?

Use the amount added to the cells, typically 10 pg to 100 pg of a control plasmid. More DNA can saturate the cells and lower the apparent efficiency.

What if I diluted the culture?

Enter the dilution factor, for example 10 for a tenfold dilution. The calculator multiplies the count by this factor.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.