Skip to content
Omnikalc

Aggregate blend and combined gradation calculator

Enter the gradation of a coarse and a fine stockpile and a target on a control sieve to get the share of each, the combined gradation on four sieves and the tons to take from each stockpile.

Updated on
Your inputs
%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

tons

Value out of range

Results

Share of the coarse stockpile

44.2 %

The target can be reached with these two stockpiles
Share of the fine stockpile
55.8 %
Blend passing the 3/8 in sieve
83.2 %
Blend passing the No. 4 sieve
60.0 %
Blend passing the No. 16 sieve
32.0 %
Blend passing the No. 200 sieve
2.1 %
Coarse stockpile to take
441.9 tons
Fine stockpile to take
558.1 tons

The aggregate blend calculator finds the proportion of two stockpiles that gives a target percent passing a control sieve, and gives the combined gradation on four sieves and the tons to take from each stockpile.

How the calculation works

  • Enter the percent passing four sieves for the coarse stockpile and for the fine stockpile.
  • Choose the control sieve and enter the target percent passing it, then the total weight of the blend.
  • The calculator solves the share of each stockpile, gives the combined gradation on the four sieves and the weight to take from each stockpile.

Example

A coarse stockpile passes 12 % of the No. 4 sieve and a fine stockpile passes 98 %. To get 60 % passing the No. 4, the share of the coarse stockpile is (98 − 60) / (98 − 12) = 44.2 % and of the fine one 55.8 %. The blend then passes 83.2 % of the 3/8 in, 60.0 % of the No. 4, 32.0 % of the No. 16 and 2.1 % of the No. 200. For 1,000 tons take 442 tons of the coarse stockpile and 558 tons of the fine one.

Why it matters

The calculator helps concrete and asphalt technicians, quarry staff, contractors and students to blend a coarse and a fine aggregate for a mix, to check how the blend meets the specification limits and to plan the loader feed.

Good to know

Use the gradation of the current sieve analysis of each stockpile, not the value of the last year, and average several samples. Check the combined percent passing on every sieve against the limits of the specification or the band of the mix design, and look at the 0.075 mm or No. 200 fines, which are sensitive to small changes. Aggregates segregate in stockpiles, so sample at several places. Weigh the blend on the feeders or the scale and adjust when the next sieve analysis differs. A blend that passes on paper must still be checked with a real sample.

The fineness modulus calculator summarizes a sieve analysis, the soil gradation calculator gives the coefficients of a gradation curve, the stockpile volume calculator gives the tons of a pile and the concrete yield calculator checks the volume of the batch.

Frequently asked questions

How are two stockpiles blended?

The percent passing of a blend on each sieve is the weighted average of the percents passing of the two stockpiles, with the shares as weights. If a is the share of the coarse stockpile, the blend passing is a × coarse + (1 − a) × fine on every sieve. Setting that equal to the target on one sieve gives the share directly.

Which sieve should I use as the control?

Use the sieve where the specification is the most critical or where the two stockpiles differ the most, often the No. 4 for a concrete or an asphalt mix. The other sieves then follow from the share, and you must check them against the limits of the specification. If any falls outside, another stockpile or another control sieve may be needed.

What if the share is below 0 or above 100?

Then the target cannot be reached with these two stockpiles, because it is finer than both or coarser than both on the control sieve. The calculator marks it. You need a third stockpile or a different material to bring the gradation to the target.

What does the calculator leave out?

The calculator leaves out the segregation and breakage of the aggregates in handling, the moisture of the stockpiles, the variation of the gradation from one sample to another and the specific gravity if you want the blend by volume. It gives the blend by weight at the gradation that you enter.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.