Skip to content
Omnikalc

Soil gradation calculator: Cu, Cc and the grading of a sand or gravel

Enter the D10, D30 and D60 sizes read on a grain-size curve to get the coefficient of uniformity, the coefficient of curvature, the USCS well graded check and a Hazen estimate of the permeability.

Updated on
Your inputs
mm

Value out of range

mm

Value out of range

mm

Value out of range

Results

Coefficient of uniformity Cu = D60 / D10

15.0

Widely graded: many grain sizes
Coefficient of curvature Cc = D30² / (D10 D60)
1.67
Smooth, well-shaped grading curve
Well graded check (1 = yes, 0 = no)
1
Well graded (GW or SW)
Hazen permeability estimate k = 100 D10²
0.0144 cm/s

The gradation of a soil describes the range of its grain sizes. The soil gradation calculator computes the coefficient of uniformity Cu and the coefficient of curvature Cc from D10, D30 and D60, checks if a sand or a gravel is well graded, and gives a Hazen estimate of the permeability.

How the calculation works

  • Read the three characteristic sizes from the grain-size curve of a sieve analysis: D10, D30 and D60 are the sizes in millimeters for which 10%, 30% and 60% of the soil by weight is finer.
  • Choose the dominant soil type: sand if more than half of the coarse fraction passes the No. 4 sieve (4.75 mm), gravel if not.
  • The calculator computes the coefficient of uniformity Cu = D60 / D10 and the coefficient of curvature Cc = D30² / (D10 × D60).
  • A clean sand is well graded if Cu is 6 or more and Cc is between 1 and 3. For a gravel, Cu must be 4 or more. The tool also gives a Hazen estimate of the permeability.

Example

A sand has D10 = 0.12 mm, D30 = 0.6 mm and D60 = 1.8 mm. The coefficient of uniformity is 1.8 / 0.12 = 15.0. The coefficient of curvature is 0.6² / (0.12 × 1.8) = 0.36 / 0.216 = 1.67. Cu is more than 6 and Cc is between 1 and 3, so the sand is well graded (symbol SW if it has less than 5% fines). The Hazen estimate of the permeability is 100 × 0.012² = 0.0144 cm/s.

Why it matters

The calculator helps geotechnical engineers, civil engineering students, drainage contractors and soil technicians to classify a granular soil after a sieve analysis, to choose a fill, a filter or a drainage sand, and to anticipate its compaction behavior. A well graded soil packs tighter and carries more load than a uniform one.

Good to know

Read D10, D30 and D60 on a smooth curve through a sieve analysis with at least six sieves. Do not apply the test if the soil has more than 12% fines, since the classification then depends on the Atterberg limits. Remember that a high Cu with a Cc outside 1 to 3 is a gap-graded soil, not a well graded one.

The Atterberg limits calculator classifies the fine fraction, the soil compaction calculator uses the grading to predict the density, Darcy’s law calculator turns a permeability into a flow and the porosity and void ratio calculator links the densities of the soil.

Frequently asked questions

What are D10, D30 and D60?

They are points on the grain-size distribution curve of a soil, from a sieve analysis. D10 is the grain diameter for which 10% of the soil weight is finer, D30 for 30% and D60 for 60%. D10 is also called the effective size, because it controls the permeability of a clean sand. The three sizes are read in millimeters on the curve, between the two sieves that surround the percentage.

What do Cu and Cc mean?

The coefficient of uniformity Cu = D60 / D10 measures the width of the grain-size range: a value near 1 means that the grains have almost one size, and a large value means a wide range. The coefficient of curvature Cc = D30² / (D10 D60) measures the shape of the curve. A value between 1 and 3 indicates a smooth curve without a missing size range.

When is a soil well graded?

In the Unified Soil Classification System, a gravel is well graded (GW) if Cu is at least 4 and Cc is between 1 and 3, and a sand is well graded (SW) if Cu is at least 6 and Cc is between 1 and 3. The test applies to soils with less than 5% of fines. A soil that does not meet both conditions is poorly graded (GP or SP).

How reliable is the Hazen permeability?

The Hazen formula k = C × D10², with C close to 100 when k is in cm/s and D10 in cm, gives only an order of magnitude. It works for clean, loose sands with a D10 between 0.1 and 3 mm and a Cu below 5. For a well graded, compacted or silty soil, it overestimates the permeability, and a lab or field test gives a better value.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.