Skip to content
Omnikalc

Stockpile volume and tonnage calculator

Enter the shape, the height, the angle of repose, the length for a windrow and the density to get the base width, the volume and the weight of the stockpile.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

ft

Value out of range

lb/ft³

Value out of range

Results

Weight of the material

854.3 tons

Width of the base
57.13 ft
Volume
17,087 ft³
Volume in cubic yards
632.9 yd³

The stockpile volume calculator gives the width of the base, the volume and the weight of a conical pile or a windrow, from its height, the angle of repose of the material, the length of the straight part and the bulk density.

How the calculation works

  • Choose the shape of the pile and enter its height and the angle of repose of the material.
  • For a windrow, enter the length of the straight part. Enter the bulk density.
  • The calculator finds the width of the base, the volume and the weight of the stockpile.

Example

A conical pile of crushed stone 20 ft high with an angle of repose of 35 degrees has a radius of 20 / tan 35° = 28.56 ft, that is a base of 57.13 ft. The volume is π × 28.56² × 20 / 3 = 17,087 ft³, or 632.9 yd³. With a bulk density of 100 lb/ft³ the pile weighs 17,087 × 100 / 2,000 = 854.3 tons.

Why it matters

The calculator helps quarry and plant operators, site managers, estimators and landscapers to size the footprint of a pile of aggregate, soil or mulch, to check the quantity of a delivery or of an inventory, and to plan the trucks and the storage.

Good to know

Measure the height of the pile and the real angle on the site, not a table value, if the material is important. Leave room around the base for the loader, and keep a distance from the walls, since a pile can push on them. For an inventory, cross-check the calculated tonnage with the weight tickets of the deliveries and the consumption, and survey large piles.

The angle of repose calculator gives the angle of a material from a pile, the dump truck loads calculator gives the loads to haul a volume, the earthwork swell and shrink calculator converts the volumes of soil and the landscape rock calculator gives the tons of decorative stone.

Frequently asked questions

How is the volume of a cone found?

A conical pile has a height H and a base radius R that follow from the angle of repose, R = H / tan(angle). The volume is one third of the area of the base times the height, π R² H / 3. Because the radius depends on the angle, a small change of the angle changes the volume a lot: with the same height, the volume at 30 degrees is about 1.7 times the volume at 40 degrees.

What about a windrow?

A windrow is a long pile with a triangular cross-section, made by a conveyor or a loader. The calculator adds the volume of the straight part, the cross-section area H² / tan(angle) times the length, to the volume of a cone that forms the two ends. Enter the length of the straight part only, without the ends. For a pile with a flat top, calculate the cone to the real height and subtract the part above.

What angle of repose should I use?

Typical angles of repose of loose dry material are 35 to 40 degrees for crushed stone and gravel, 30 to 35 degrees for sand, 35 to 45 degrees for cement, 25 to 35 degrees for coal and 28 to 40 degrees for wood chips. A wet or fine material may stand steeper. A measured value from your own pile is the best, and the angle falls when the material is dropped from a greater height.

What does the calculator leave out?

The calculator assumes a symmetrical pile on a flat ground, with a sharp top, a constant bulk density and no loss. Real piles are lower at the top, spread on a slope, compacted at the bottom, and wet at the surface. For an inventory or a payment, survey the pile with a drone or a total station, and use the calculated value to estimate the footprint and the order of magnitude.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.