Skip to content
Omnikalc

Press brake tonnage calculator: how much force to bend a sheet

Enter the thickness, the length of the bend, the tensile strength and the V die opening to get the air bending force in tons and per foot, the minimum flange length and the inside bend radius.

Updated on
Your inputs
in

Value out of range

in

Value out of range

ksi

Value out of range

in

Value out of range

Results

Air bending force

47.9 US tons

Ratio of the die opening to the thickness V / t
8.0
Usual range for air bending
Air bending force per foot of bend
11.98 tons/ft
Minimum flange length (0.7 V)
1.05 in
Inside bend radius in air bending (0.156 V)
0.234 in

A press brake bends a sheet between a punch and a V die. The press brake tonnage calculator estimates the air bending force from the thickness, the length, the tensile strength and the die opening, and gives the minimum flange length and the inside radius.

How the calculation works

  • Enter the thickness of the sheet, the length of the bend, the tensile strength of the material and the width of the V die opening. A common rule is a die opening of 8 times the thickness for mild steel.
  • The calculator uses the air bending formula F = 1.42 × σu × L × t² / V, where F is the force, σu the tensile strength, L the length of the bend, t the thickness and V the die opening.
  • It gives the force in US tons and per foot of bend, which is how the tonnage charts of the press brake makers are expressed.
  • It also gives the minimum flange length, about 0.7 V, and the inside bend radius, about 0.156 V, that the air bending produces.

Example

A 3/16 in (0.1875 in) sheet of mild steel with a tensile strength of 60 ksi is bent over 48 in in a 1.5 in V die. The ratio V / t is 8.0. The bending force is 1.42 × 60,000 × 48 × 0.1875² / 1.5 = 95,850 lb, or 47.9 US tons, which is 11.98 tons per foot. The minimum flange length is 1.05 in and the inside radius in air bending is 0.234 in.

Why it matters

The calculator helps sheet metal fabricators, press brake operators, estimators, product designers and students to check if a machine can make a bend, to choose a die opening and to see what happens when the thickness or the material changes. A small increase in thickness raises the force strongly, since the force goes with the square.

Good to know

Use the tensile strength of the actual sheet. Do not bend more than about 80% of the capacity of the machine, and not at the ends of the table. Keep the flange longer than 0.7 V. Increase the die opening for a thicker sheet, and follow the minimum bend radius of the material to avoid cracks.

The bend allowance calculator gives the flat length of the part, the hydraulic press calculator sizes the cylinder, the Young’s modulus calculator covers the springback and the true stress and strain calculator relates the strength to the strain.

Frequently asked questions

What is air bending?

In air bending, the punch pushes the sheet into a V die without touching the bottom of the die. The angle depends on the depth of the stroke. It needs less force than bottoming or coining, it allows several angles with one tool and it is the most common method on press brakes. The inside radius is a fraction of the die opening, about 15% to 17% of V for mild steel.

What is the formula of the force?

The usual formula is F = C × σu × L × t² / V, where C is a constant close to 1.33 to 1.42. A tensile strength of 60 ksi (415 MPa) is typical of mild steel. The force grows with the square of the thickness, and in direct proportion to the length of the bend and the strength. A wider die reduces the force, but increases the radius and the minimum flange.

How do I choose the V die opening?

A common rule for mild steel is a die opening of 8 times the thickness for sheets up to 3/8 in (10 mm) thick, and 10 to 12 times for thicker plate. A narrower die gives a tighter radius, but the force is higher and the risk of cracking increases. The minimum flange length is about 0.7 times the die opening, because the sheet must rest on both sides of the die.

What are the limits of this calculator?

The formula is an estimate for air bending of mild steel at room temperature. Stainless steel needs about 1.5 times the force, and soft aluminum about 0.5 times, which is included in the tensile strength. The force also depends on the springback, the speed and the lubrication. The press brake has a limit of force per unit length, and a short tool or a short bend concentrates the load. Check the chart of the machine.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.