Skip to content
Omnikalc

Basal heave calculator: stability of the bottom of an excavation in clay

Enter the depth, the width and the length of the excavation, the unit weight and the undrained strength of the clay and the surcharge to get Nc, the overburden pressure, the safety factor against basal heave and the limit depth.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

pcf

Value out of range

psf

Value out of range

psf

Value out of range

Results

Factor of safety against basal heave

1.68

Safety factor of 1.5 or more: usual minimum for a temporary excavation
Bearing capacity factor Nc
6.11
Overburden pressure at the excavation level
2,550 psf
Depth for a safety factor of 1.5
22.6 ft

The basal heave calculator gives the bearing capacity factor Nc, the overburden pressure, the factor of safety against basal heave and the limit depth of an excavation in soft clay, by the Bjerrum and Eide method, from the geometry, the unit weight, the undrained strength and the surcharge.

How the calculation works

  • Enter the depth, the width and the length of the excavation.
  • Enter the unit weight of the soil, the undrained shear strength of the clay below the bottom and the surcharge at the surface.
  • The calculator finds the bearing capacity factor Nc of Bjerrum and Eide, the overburden pressure at the excavation level, the factor of safety against basal heave and the depth that gives a factor of 1.5.

Example

An excavation of 20 ft of depth, 40 ft of width and 100 ft of length is made in a clay with a unit weight of 115 pcf and a strength su of 700 psf, with a surcharge of 250 psf. Nc = 5.14 × (1 + 0.2 × 40 / 100) × (1 + 0.2 × 20 / 40) = 6.11. The overburden is 115 × 20 + 250 = 2,550 psf. The safety factor is 6.11 × 700 / 2,550 = 1.68, which is above 1.5. The depth for a factor of 1.5 is (6.11 × 700 / 1.5 − 250) / 115 = 22.6 ft.

Why it matters

The calculator helps geotechnical and structural engineers, excavation contractors and students to check the stability of the bottom of a deep excavation in clay in a first design and to see how the depth, the width and the strength change the safety factor.

Good to know

Use the undrained strength from vane or triaxial tests at the depth below the bottom, with a conservative value. Check also the wall embedment, the bracing, and the groundwater. Watch the movements during the excavation with the monitoring, and have an action plan if the movements are higher than expected.

The bearing capacity calculator uses the same logic for footings, the Rankine earth pressure calculator gives the lateral loads on the wall, the soil unit weight calculator gives γ and the sheet pile embedment calculator sizes the wall.

Frequently asked questions

What is basal heave?

Basal heave is the upward movement of the bottom of an excavation in soft clay, caused by the weight of the soil on the sides, which pushes the soil at the bottom like a bearing capacity failure turned upside down. The soil at the sides acts as a surcharge on a footing at the bottom. It can cause the collapse of the walls, large settlements outside the excavation and damage to the adjacent structures.

How is the safety factor found?

The calculator uses the method of Bjerrum and Eide for the clay with a constant undrained strength. The factor Nc = 5.14 (1 + 0.2 B/L)(1 + 0.2 H/B) is limited to 7.5 and grows with the depth, then the safety factor is FS = Nc su / (γ H + q). A value of 1.5 or more is usually asked for a temporary excavation, and a higher value when there are sensitive structures or no possibility to monitor.

How can the safety factor be increased?

The usual ways are to use a wall that goes deeper under the bottom, which gives a longer failure path, to improve the soil under the bottom with jet grouting or deep mixing, to reduce the surcharge, to excavate in stages with the bracing, or to make the excavation in a cofferdam with a concrete slab. Dewatering helps only when the failure comes from the water pressure, not from the undrained strength.

What are the limits of the calculator?

The method assumes a uniform clay below the bottom, a strength that does not change with depth and no hard layer near the bottom, which would give a higher safety factor. It does not cover the sand layers with water pressure and the piping, the wall stiffness, or the time effect. A geotechnical engineer should check the excavation design with the soil investigation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.