Skip to content
Omnikalc

Cantilever sheet pile embedment calculator: embedment depth of a sheet pile wall in granular soil

Enter the retained height, the soil friction angle and unit weight, the factor of safety and the extra embedment to get Ka, Kp, the theoretical and design embedment depths, the total length and the active thrust of a cantilever sheet pile wall.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

lb/ft³

Value out of range

Value out of range

%

Value out of range

Results

Design embedment depth (with extra length)

13.06 ft

Active earth pressure coefficient Ka
0.307
Passive earth pressure coefficient Kp
3.255
Theoretical embedment depth
10.89 ft
Total sheet pile length
23.06 ft
Active thrust on the wall
8,043 lb/ft

The cantilever sheet pile embedment calculator gives the active and passive coefficients, the theoretical and design embedment depth, the total length and the active thrust of a cantilever sheet pile wall in granular soil, with a factor of safety.

How the calculation works

  • Enter the retained height of soil above the excavation or dredge level, the friction angle and the unit weight of the granular soil.
  • Enter the factor of safety applied to the passive resistance (1.5 is common), and the extra embedment added for the real pressure reversal near the tip (20 to 30%).
  • The calculator computes Rankine’s coefficients Ka = tan²(45° − φ/2) and Kp = 1 / Ka.
  • It balances the moments about the tip, Ka (H + D)³ = Kp D³ / FS, to get the theoretical embedment D = H / [(Kp / FS Ka)^(1/3) − 1], and gives the design embedment and the total length.

Example

A cantilever sheet pile wall retains 10 ft of sand with φ = 32° and 120 lb/ft³. Then Ka = 0.307 and Kp = 3.255. With a factor of safety of 1.5, the ratio (Kp / (1.5 × Ka))^(1/3) is 1.9185, so the theoretical embedment is 10 / (1.9185 − 1) = 10.89 ft. Adding 20% gives a design embedment of 13.06 ft and a total length of 23.06 ft. The active thrust on the wall is 0.5 × 120 × 0.307 × 20.89² = 8,043 lb/ft.

Why it matters

The calculator helps civil and geotechnical engineers, contractors, marine and waterfront designers, and students to make a first estimate of the length of sheet piling for a temporary or permanent wall, and to see how the soil strength and the factor of safety change the embedment. It supports quantity estimates before a full design.

Good to know

Use a conservative friction angle from the soil report. Include the water table and any surcharge in the final design, since they change the length a lot. Compute the maximum bending moment to choose the section. Check the deflection and the effect of the excavation on the neighboring structures.

The Rankine earth pressure calculator gives the pressure coefficients, the retaining wall calculator covers gravity walls, the soil unit weight calculator converts soil weights and the timber lagging thickness calculator covers temporary shoring boards.

Frequently asked questions

What is a cantilever sheet pile wall?

A cantilever sheet pile wall is a row of interlocking steel, concrete or vinyl sheets driven into the ground, which holds back the soil only by the passive resistance of the soil in front of its embedded part, with no anchor or brace. It is economical for retained heights up to about 15 ft (4.5 m) in firm ground. Higher walls need an anchor or a brace, as the embedment and the bending moment grow very quickly.

How is the embedment computed?

The wall is in equilibrium when the overturning moment of the active earth pressure on the retained height and the embedded depth balances the resisting moment of the passive pressure in front, about the tip. With a triangular pressure on both sides, Ka (H + D)³ = Kp D³ / FS. Solving for D gives the closed-form result. The factor of safety is applied to the passive resistance.

Why add extra embedment?

The simple method ignores the fact that the net pressure changes sign near the tip, with a passive resistance behind the wall at the bottom. A full analysis, with the net pressure diagram, requires an iterative solution and gives a depth about 20 to 40% larger than the simple method when no factor of safety is applied. Adding 20 to 30% to the embedment, as the calculator allows, covers this effect in a preliminary design.

What does the calculator not include?

It assumes a homogeneous granular soil with no cohesion, no water table and no surcharge, and a smooth wall. Water, a surcharge, layered soils or clay need a more advanced analysis, with the net hydrostatic pressure and the real soil profile. The bending moment of the wall, which sets the section modulus of the sheet pile, and the deflection at the top also have to be computed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.