Skip to content
Omnikalc

How deep should a flagpole be set, and how much concrete?

Enter the pole height above ground, the burial depth as a share of that height, the pole diameter at the base, the hole diameter and the concrete bag yield: get the burial depth, the total pole length, the concrete, the bags and a matching flag size.

Updated on
Your inputs
ft

Value out of range

%

Value out of range

in

Value out of range

in

Value out of range

cu ft

Value out of range

Results

Burial depth

24 in

Concrete bags

4

Total pole length
22.0 ft
Concrete
1.96 cu ft
Flag length (about 1/4 of the height)
5.0 ft
Follow the pole maker's footing chart, which allows for wind in your area; check HOA rules before you dig, and call 811 to locate buried lines

A flagpole has to resist the wind pushing on a flag high above the ground, so most of its strength comes from what you cannot see: the footing. This calculator works out how deep to set the pole, the total length to buy, the concrete for the hole, the number of bags, and a flag size that looks right on that pole.

How the calculation works

  • Burial depth = height above ground × burial share (10% is the usual rule for residential in-ground poles)
  • Total pole length = height above ground + burial depth
  • Concrete = π ÷ 4 × (hole diameter² − pole diameter²) × burial depth
  • Bags = concrete ÷ yield per bag, rounded up
  • Flag length ≈ height above ground ÷ 4

For a 20 ft pole set 10% of its height in the ground, the hole is 24 in deep and the pole 22 ft long. A 14 in hole around a 4 in pole takes about 1.96 cu ft of concrete, or 4 bags of 0.6 cu ft (the yield of an 80 lb bag). A flag about 5 ft long, a 3 × 5 ft flag, suits it.

Typical pole and flag sizes

Pole above ground Flag size
15 to 20 ft 3 × 5 ft
20 to 25 ft 4 × 6 ft
30 to 35 ft 5 × 8 ft
40 ft 6 × 10 ft

A flag that is too big for its pole strains the halyard and the footing in strong wind, and wears out quickly.

Ground sleeve or direct burial

Most residential poles today sit in a ground sleeve: a tube set in concrete that the pole slides into, so it can be removed or replaced. The sleeve is a little wider than the pole, so use its outside diameter in the calculator. Some makers ask for a deeper footing in sandy soil, in frost areas or in high-wind zones; their chart takes priority over the 10% rule.

Setting the footing

  1. Call 811 a few days before you dig, so buried lines are marked.
  2. Dig the hole about 6 in deeper than the burial depth and add gravel at the bottom for drainage.
  3. Set the sleeve or pole, check it is plumb on two sides and brace it.
  4. Pour the concrete, sloping the top away from the pole so water runs off.
  5. Let it cure the time on the bag, usually a few days, before raising the flag.

Check homeowners’ association rules on pole height and flag display before you buy.

Frequently asked questions

How deep should a flagpole be buried?

About 10% of its height above ground: 24 in for a 20 ft pole, unless the maker's chart asks for more.

How long a pole do I need for 20 ft above ground?

About 22 ft, with 2 ft set in the ground.

How much concrete for a 20 ft flagpole?

A 14 in hole 24 in deep around a 4 in pole takes about 1.96 cu ft, or 4 bags of 0.6 cu ft.

What size flag for a 20 ft flagpole?

A flag about a quarter of the height, so 3 × 5 ft; a 4 × 6 ft flag suits poles of 20 to 25 ft.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.