Skip to content
Omnikalc

Consolidation settlement calculator: how far and how fast will the clay settle?

Enter the clay thickness, the void ratio, the compression index and the stresses to get the primary settlement and the time for 50 % and 90 % consolidation.

Updated on
Your inputs
ft

Value out of range

Value out of range

Value out of range

psf

Value out of range

psf

Value out of range

ft²/day

Value out of range

Results

Primary consolidation settlement

4.2 in

Strain of the layer
3.50 %
Void ratio after consolidation
0.833
Time for 50 % consolidation
49.3 days
Time for 90 % consolidation
212.0 days

A building or an embankment on soft clay can keep sinking for years after it is finished. The consolidation settlement calculator takes the layer thickness, the void ratio, the compression index, the stress before and after loading, the coefficient of consolidation and the drainage, and gives the primary settlement, the strain, the final void ratio and the times for 50 % and 90 % consolidation.

How the calculation works

  • Enter the thickness of the clay layer, its initial void ratio and its compression index Cc, from a consolidation test.
  • Enter the effective stress at the middle of the layer before loading and the stress increase from the new load.
  • The settlement is Sc = Cc × H / (1 + e₀) × log₁₀((σ’₀ + Δσ) / σ’₀), for a normally consolidated clay.
  • Enter the coefficient of consolidation and the drainage to get the time: t = Tv × Hdr² / cv, with Tv = 0.197 for 50 % and 0.848 for 90 % consolidation.

Example

A clay layer is 10 ft thick, with e₀ = 0.9 and Cc = 0.30. The effective stress at mid-layer is 1,500 psf and a new load adds 1,000 psf. The settlement is 0.30 × 10 / 1.9 × log₁₀(2,500 / 1,500) = 0.350 ft, or 4.20 in, a strain of 3.50 %. The void ratio falls to 0.833. With sand above and below, the drainage path is 5 ft, and with cv = 0.1 ft²/day, 50 % consolidation takes 49.3 days and 90 % takes 212 days.

Why it matters

Total settlement and differential settlement decide whether a structure cracks, whether a road needs repaving and how long you must wait before building on a preloaded site. Computing the settlement and the time lets you compare options such as preloading, vertical drains, lighter fill or deep foundations before the first test pit is dug.

Good to know

The calculator treats the layer as one homogeneous, normally consolidated clay with the stress taken at mid-layer, and one-dimensional compression under a wide load. Thick layers should be split into sublayers, narrow footings spread the stress with depth, and secondary compression (creep) comes on top of the primary settlement. Use parameters from site tests and treat the result as a first estimate.

The porosity and void ratio calculator covers soil phase relations, the footing size calculator sizes footings on soil, the retaining wall calculator checks walls retaining soil, and the soil loss calculator estimates erosion from slopes.

Frequently asked questions

What is consolidation settlement?

When you load a saturated clay, the water in its pores must flow out before the soil can compress. This slow squeezing out of water makes the ground settle over months or years. The final settlement depends on the compressibility of the clay and the stress increase, and the speed depends on how easily the water drains.

What is the compression index?

The compression index Cc is the slope of the void ratio against the logarithm of the effective stress on the virgin compression line, measured in an oedometer test. Soft clays have values from about 0.2 to 1 or more. When no test is available, correlations with the liquid limit, such as Cc = 0.009 × (LL − 10), give a rough estimate.

Why does drainage matter so much?

The time to consolidate grows with the square of the longest drainage path. A layer that drains on both faces has a path of half the thickness and consolidates four times faster than the same layer that drains on one face only. Sand drains or wick drains shorten the path further and are used to speed up settlement.

Does the formula apply to overconsolidated clay?

No. The calculator assumes a normally consolidated clay on its virgin compression line. For an overconsolidated clay whose final stress stays below the preconsolidation pressure, the settlement uses the much smaller recompression index Cr instead. The calculation is then split into two parts if the stress crosses the preconsolidation pressure.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.