Skip to content
Omnikalc

Effective stress calculator: how much of the soil weight is carried by the grains?

Enter the water table depth, the unit weights and the depth of interest to get the total stress, the pore water pressure and the effective stress.

Updated on
Your inputs
ft

Value out of range

pcf

Value out of range

pcf

Value out of range

ft

Value out of range

Results

Effective vertical stress

1,536.4 psf

Total vertical stress
2,410.0 psf
Pore water pressure
873.6 psf
Effective stress as a share of total
63.8 %
Change in effective stress if the water table rises 1 ft
-47.4 psf

Soil is a skeleton of grains with water in the gaps, and only the grain skeleton gives the soil its strength. The effective stress calculator takes the water table depth, the unit weights of the soil above and below it and the depth of interest, and gives the effective vertical stress, the total stress, the pore water pressure, the effective share and the change when the water table rises by one unit.

How the calculation works

  • Enter the depth of the water table below the ground and the depth at which you want the stresses.
  • Enter the unit weight of the soil above the water table and the saturated unit weight below it.
  • The total vertical stress is the weight of everything above: γ₁ × depth above the water table + γsat × depth below it.
  • The pore water pressure is γw × depth below the water table, with γw = 62.4 pcf. Terzaghi’s effective stress is the total stress minus the pore pressure, σ’ = σ − u, and it controls the strength and compression of the soil.

Example

The water table is 6 ft down. The soil above weighs 110 pcf and the saturated soil below weighs 125 pcf. At 20 ft, the total stress is 110 × 6 + 125 × 14 = 2,410 psf. The pore pressure is 62.4 × 14 = 873.6 psf, so the effective stress is 1,536.4 psf, or 63.8 % of the total. If the water table rose by 1 ft, one more foot of soil would go from 110 to 125 pcf, but the water pressure would rise by 62.4 psf, and the effective stress would fall by 47.4 psf.

Why it matters

Effective stress sits behind almost every calculation in soil mechanics: bearing capacity, slope stability, settlement and earth pressure all use it. Seeing how a rising water table cuts it explains floods that lift basements, slopes that fail after rain and foundations that settle when groundwater is pumped.

Good to know

The calculator models a uniform soil above and one below the water table, with hydrostatic water pressure. It ignores seepage, artesian pressure, capillary rise and layers with different unit weights. For real design, divide the profile into layers and use data from a site investigation. Treat the result as a teaching figure.

The porosity and void ratio calculator covers soil phase relations, the retaining wall calculator uses effective stresses behind walls, the footing size calculator sizes footings on soil, and the soil loss calculator estimates erosion.

Frequently asked questions

What is effective stress?

It is the part of the total stress carried by the contacts between soil grains. Karl Terzaghi showed that the strength and the compression of a soil depend on this effective stress and not on the total stress, so the weight of water in the voids does not give the soil strength. The formula is the total stress minus the pore pressure.

Why does the water table matter?

Below the water table, the pores are full of water that pushes in all directions. This pressure grows with depth at about 62.4 psf per foot or 9.81 kPa per metre and reduces the stress between grains. A higher water table lowers the effective stress and so the shear strength and the bearing capacity.

What happens above the water table?

In a simple model, the pore pressure is zero above the water table and the effective stress equals the total stress. In reality, fine soils hold water by suction above the water table, which adds to the effective stress. The calculator ignores this capillary effect, which is on the safe side.

How does it relate to the buoyant unit weight?

Under the water table, the effective weight of the soil is its saturated unit weight minus the unit weight of water. This buoyant unit weight is about 62.6 pcf for a soil with a saturated weight of 125 pcf. The effective stress below the water table grows with depth at this rate.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.