Skip to content
Omnikalc

Braced excavation calculator: Peck apparent pressure and load on the struts

Enter the depth of the excavation, the soil type and properties and the spacing of the struts to get the active coefficient, the apparent earth pressure, the total load on the wall and the load on each strut.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

pcf

Value out of range

psf

Value out of range

ft

Value out of range

ft

Value out of range

Results

Load on each strut

71.9 kips

Active coefficient Ka
0.307
Apparent earth pressure
599 psf
Total load on the wall per foot
14,979 lb/ft

The braced excavation calculator gives the active coefficient, the Peck apparent earth pressure, the total load on the wall and the load on each strut of a braced cut in sand or clay, from the depth, the soil properties and the spacing of the struts.

How the calculation works

  • Enter the depth of the excavation and choose the soil type: sand or soft to medium clay.
  • Enter the friction angle and the unit weight of the sand, or the undrained shear strength of the clay, then the vertical and horizontal spacing of the struts.
  • The calculator finds the active coefficient, the apparent earth pressure of the Peck diagram, the total load on the wall per unit length and the load on each strut.

Example

A braced excavation in sand is 25 ft deep. The sand has φ = 32° and a unit weight of 120 pcf, and the struts are spaced 10 ft vertically and 12 ft horizontally. Ka = (1 − sin 32°) / (1 + sin 32°) = 0.307. The apparent pressure is 0.65 × 0.307 × 120 × 25 = 599 psf. The total load is 599 × 25 = 14,979 lb/ft, and the load on each strut is 599 × 10 × 12 / 1000 = 71.9 kips.

Why it matters

The calculator helps geotechnical and structural engineers, shoring contractors and students to estimate the strut loads of a trench or an excavation support in a first design, and to see how the depth and the spacing change the loads.

Good to know

Add the surcharge from the traffic and the nearby buildings, and the water pressure below the water table. Preload the struts to limit the movements, and check the buckling of the struts and the capacity of the walers. Monitor the movements and the strut loads during the work.

The Rankine earth pressure calculator gives the classical pressure, the retaining wall calculator checks a wall, the excavation calculator gives the volume of soil and the sheet pile embedment calculator sizes a cantilever wall.

Frequently asked questions

What is the Peck apparent pressure diagram?

In a braced cut, the earth pressure on the wall does not follow the triangle of the Rankine theory, because the wall moves more at the top before each strut is installed than at the bottom. Peck measured the loads on the struts in many excavations and proposed apparent pressure diagrams, which are envelopes of these loads. They are used to size the struts, the walers and the wall, not to find the real pressure.

How are the pressures found for sand and for clay?

For a sand, the diagram is a rectangle of height H and pressure 0.65 Ka γ H. For a soft to medium clay, the pressure is γ H − 4 m su with m = 1, but not less than 0.3 γ H, and the diagram is a trapezoid. The calculator uses the maximum pressure on the whole height, which is a simple and conservative approach for the strut loads.

How is the load on each strut found?

Each strut carries the pressure over its tributary area, which is the vertical spacing times the horizontal spacing. The load is the apparent pressure times the vertical and the horizontal spacing. For the top and the bottom struts, the tributary height is smaller than the spacing, and a more precise analysis with the hinge method is made by the designer. The result is then used for the strut buckling and the connections.

What are the limits of the calculator?

The calculator gives the strut load from the apparent pressure only. It does not include the water pressure, the surcharge, the layered soils, the preload of the struts, the temperature effect on the struts, the stability of the base or the movements of the ground. The design of a deep excavation must be made by a geotechnical and a structural engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.