Skip to content
Omnikalc

CBR calculator: California Bearing Ratio and subgrade resilient modulus

Enter the loads at 0.1 and 0.2 inch of penetration of a CBR test to get the California Bearing Ratio, the subgrade rating and the resilient modulus used in pavement design.

Updated on
Your inputs
in²

Value out of range

lb

Value out of range

lb

Value out of range

Results

California Bearing Ratio at 0.1 in

9.0 %

Fair subgrade
California Bearing Ratio at 0.2 in
8.7 %
Ratio CBR 0.2 in / CBR 0.1 in
0.96
The 0.1 in value governs, as in the standard
Resilient modulus, 1,500 × CBR
13,500 psi
Resilient modulus, 2,555 × CBR^0.64 (MEPDG)
10,426 psi

The California Bearing Ratio measures the strength of a subgrade or a base material by pushing a piston into a compacted sample. The CBR calculator turns the penetration loads into the CBR at 0.1 and 0.2 inch, rates the subgrade and estimates the resilient modulus used in the design of pavements.

How the calculation works

  • Enter the loads read on the CBR test machine when the standard piston of 3 in² has penetrated the sample by 0.1 in and by 0.2 in.
  • The calculator divides each load by the area of the piston to get the penetration stress, then divides it by the stress in a standard crushed stone: 1,000 psi at 0.1 in and 1,500 psi at 0.2 in.
  • The California Bearing Ratio (ASTM D1883) is that ratio in percent. It is normally the value at 0.1 in, unless the value at 0.2 in is higher and is confirmed by a second test.
  • The tool also converts the CBR into a resilient modulus, which is the stiffness of the subgrade used in pavement design, with two common correlations.

Example

A soaked CBR test on a clay sand gives 270 lb at 0.1 in and 390 lb at 0.2 in on the 3 in² piston. The stress at 0.1 in is 270 / 3 = 90 psi, so the CBR at 0.1 in is 90 / 1,000 = 9.0%. At 0.2 in, the stress is 130 psi and the CBR is 130 / 1,500 = 8.7%. The ratio is 0.96, so the 0.1 in value governs. The resilient modulus is 1,500 × 9.0 = 13,500 psi by the simple rule, and 2,555 × 9.0^0.64 = 10,426 psi by the MEPDG correlation.

Why it matters

The calculator helps civil engineers, road and parking lot contractors, geotechnical technicians and students to read the result of a CBR test, to classify the subgrade of a pavement and to get the stiffness input of a design method. A low CBR is the signal to stabilize the soil or to thicken the base.

Good to know

Test the soil at the density and the moisture expected in the field, and soaked if the subgrade can get wet. Do not report a CBR from a single test on a variable soil: use the average of several samples. Treat the modulus from the correlations as an estimate, and apply a safety margin in the design.

The bearing capacity calculator gives the strength of a soil under a footing, the soil compaction calculator controls the density of the subgrade, the Atterberg limits calculator classifies fine soils and the gravel calculator estimates the base course.

Frequently asked questions

What is the California Bearing Ratio?

The CBR is the ratio, in percent, of the stress needed to push a standard piston into a soil sample at a given depth to the stress needed to push it into a standard crushed stone. By definition the crushed stone has a CBR of 100%. The test is made on a compacted sample, often soaked for four days to simulate the worst moisture, and it is the most common strength index of a pavement subgrade or a granular base.

Why are there two values, at 0.1 and 0.2 inch?

The standard stress of the crushed stone is 1,000 psi (6.9 MPa) at a penetration of 0.1 in (2.5 mm), and 1,500 psi (10.3 MPa) at 0.2 in (5.0 mm). The CBR is calculated at both depths. ASTM D1883 uses the value at 0.1 in, but if the value at 0.2 in is higher, the test is repeated, and if the result is confirmed, the higher value is used.

What is the resilient modulus?

The resilient modulus Mr is the stiffness of the subgrade under a repeated wheel load, used in the AASHTO and MEPDG pavement design methods. It is hard to measure, so it is often estimated from the CBR. The rule Mr = 1,500 × CBR in psi is used for fine-grained soils with a CBR of about 10 or less. The MEPDG formula Mr = 2,555 × CBR^0.64 covers a wider range.

What are the limits of these correlations?

The correlations between CBR and Mr have a large scatter, a factor of two or more, and they depend on the soil type and the moisture. Use them for a preliminary design or a comparison between sites. For a final design, measure the resilient modulus in the laboratory, or use the results of a falling weight deflectometer or a dynamic cone penetrometer on the actual subgrade.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.