Skip to content
Omnikalc

Atterberg limits calculator: how plastic is your soil?

Enter the liquid limit, the plastic limit, the natural water content and the clay fraction to get the plasticity index, the liquidity index and the activity.

Updated on
Your inputs
%

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Results

Plasticity index PI

28.0 %

High plasticity: a clay with strong swelling and shrinkage
Liquidity index LI
0.25
Consistency index CI
0.75
Activity of the clay
0.62
PI above (+) or below (−) the A-line
4.6

Fine soils change from a hard crust to a soft slurry as they take up water, and the Atterberg limits mark the borders. The Atterberg limits calculator takes the liquid limit, the plastic limit, the natural water content and the clay fraction, and gives the plasticity index, the liquidity index, the consistency index, the activity of the clay and the position relative to the A-line.

How the calculation works

  • Enter the liquid limit LL and the plastic limit PL, the water contents, in percent, at which the soil changes from a liquid to a plastic state and from a plastic to a semi-solid state.
  • Enter the natural water content of the soil in the ground, and the clay fraction, the percentage by weight finer than 2 microns.
  • The plasticity index is PI = LL − PL. The liquidity index is LI = (w − PL) ÷ PI and the consistency index is CI = (LL − w) ÷ PI, with LI + CI = 1.
  • The activity is PI ÷ clay fraction. The A-line of the Unified Soil Classification, PI = 0.73 × (LL − 20), separates clays above it from silts below it.

Example

A soil has LL = 52 %, PL = 24 %, a natural water content of 31 % and 45 % clay. The plasticity index is 52 − 24 = 28. The liquidity index is (31 − 24) ÷ 28 = 0.25, so the soil is stiff, and the consistency index is 0.75. The activity is 28 ÷ 45 = 0.62, a normal clay. On the plasticity chart, the A-line at LL 52 is 0.73 × 32 = 23.4, so the soil sits 4.6 points above it, which makes it a fat clay (CH).

Why it matters

These indices are the first step in classifying a fine soil, and they guide decisions about foundations, embankments, roads and earthworks. A high plasticity index warns of swelling clays that crack houses, and a liquidity index near 1 warns of soft ground.

Good to know

The limits come from standard lab tests such as ASTM D4318 and need a proper soil sample. The classification here is a simplified view of the Unified Soil Classification System, and real classification also uses the grain size distribution. Use the output for learning and for checking calculations, not as a substitute for a geotechnical report.

The porosity and void ratio calculator covers soil phase relations, the soil loss calculator estimates erosion, the retaining wall calculator covers walls, and the angle of repose calculator deals with loose material.

Frequently asked questions

What are the Atterberg limits?

They are water contents that mark the borders between the states of a fine-grained soil. At the liquid limit, the soil starts to flow like a liquid. At the plastic limit, it stops being mouldable and crumbles. The plastic state lies between the two. They are found in the lab with the Casagrande cup or the cone test and the thread rolling test.

What does the plasticity index tell you?

The plasticity index, the difference between the liquid limit and the plastic limit, is the range of water contents over which the soil is plastic. A high value means a clay that swells when wet and shrinks when dry, with high compressibility and low permeability. A low value means a silt or a sandy soil.

What are the liquidity and consistency indices?

The liquidity index shows where the natural water content falls between the limits. A value near 0 means the soil is near its plastic limit and stiff. A value near 1 means it is near the liquid limit and soft. A value above 1 means the soil would flow if remoulded, as in some sensitive clays.

What is the A-line?

The A-line on the plasticity chart divides clays from silts and organic soils in the Unified Soil Classification System. Points above it with LL above 50 are fat clays (CH), and those above it with LL below 50 are lean clays (CL). Points below are silts (ML or MH) or organic soils.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.