Skip to content
Omnikalc

Channel section shear center and torque calculator

Enter the flange and web dimensions of a channel and the load line to get the centroid, the shear center and the torque that a load applied away from the shear center puts on the section.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

kips

Value out of range

in

Value out of range

Results

Shear center from the web centerline

0.924 in

Area of the section
4.48 in²
Centroid from the web centerline
0.608 in
Moment of inertia about the strong axis
67.9 in⁴
Shear center from the back of the web
1.044 in
Torque on the channel
5.5 kip-in

The channel shear center calculator gives the centroid and the shear center of a channel section from its flange and web dimensions, and the torque put on it by a load that is not through the shear center.

How the calculation works

  • Enter the flange width (from the web centerline), the distance between the flange centerlines and the thicknesses of the flange and the web.
  • Enter the shear load and the distance of its line of action from the web centerline.
  • The calculator gives the centroid, the shear center, and the torque that the channel must resist when the load is not through the shear center.

Example

A channel has flanges 2.5 in wide (from the web centerline), 9.6 in between the flange centerlines, a flange of 0.436 in and a web of 0.24 in. Its strong axis inertia is 67.9 in⁴. The shear center is e = 0.436 × 2.5² × 9.6² / (4 × 67.9) = 0.92 in from the web centerline, on the side away from the flanges, which is 1.04 in from the back of the web. A load of 6 kips in the plane of the web has an arm of 0.92 in and a torque of 5.55 kip-in.

Why it matters

The calculator helps structural engineers, fabricators and students to understand why a channel twists under a load in its web, to find where a load should act and to estimate the torque to give to the bracing or the connection.

Good to know

Take the dimensions to the centerline of the plates, since the thin-wall formula uses the centerline geometry, so the flange width is the width of the flange minus half of the web thickness. For a rolled channel, the values of the shape tables are better, and they give the shear center as the distance from the center of the web. Remember that the shear center is outside the web, so a load on the web needs a torque even when it seems centered. Check also that the load line used is the real line of action of the load, which can be on the top of the flange.

The shaft torsion calculator gives the shear stress of a round shaft, the beam lateral-torsional buckling calculator checks a beam without lateral support, the section modulus calculator gives the bending stress and the moment of inertia calculator gives the properties of simple shapes.

Frequently asked questions

What is the shear center?

The shear center is the point in the cross section through which a transverse load must act for the section to bend without twisting. For a section with two axes of symmetry, such as an I beam, it is at the centroid. A channel has only one axis of symmetry, and its shear center is outside the web, on the side opposite to the flanges.

Why does a channel twist?

The shear flow in the flanges of a channel adds up to two forces in opposite directions, a couple, which the web shear alone cannot balance. A load through the centroid or the web does not pass through the shear center, so it twists the channel as it bends it. A load through the shear center bends it without twisting.

How do I stop the twist?

Apply the load through the shear center, for example with a plate or a bracket, or brace the channel against rotation with ties, decking or a second member, so the torque goes to the bracing. Often a channel is used in pairs back to back, or as a boxed section, which brings the shear center to the middle.

What does the calculator leave out?

The calculator uses the thin-walled model with straight flanges of constant thickness, so it differs from a rolled channel with tapered flanges and fillets by a few percent. It leaves out the warping stresses and the torsional constants. For design, use the shear center of the shape tables and the AISC torsion guide.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.