Skip to content
Omnikalc

Muskingum channel routing outflow calculator

Enter the storage constant K, the factor X, the time step, the inflows and the starting outflow to get the routing coefficients and the outflow of a channel reach.

Updated on
Your inputs
h

Value out of range

Value out of range

h

Value out of range

cfs

Value out of range

cfs

Value out of range

cfs

Value out of range

Results

Outflow at the end of the step

985.7 cfs

Coefficient C0
0.0476
Coefficient C1
0.4286
Coefficient C2
0.5238
Water stored in the reach at the end
1,139.1 acre-ft
Time step check (1 = valid)
1
The time step gives positive coefficients

The Muskingum routing calculator gives the coefficients C0, C1 and C2, the outflow of a channel reach at the end of a time step, the water stored in the reach and a check of the time step.

How the calculation works

  • Enter the storage constant K, the weighting factor X and the time step of the routing.
  • Enter the inflow at the start and at the end of the step and the outflow at the start.
  • The calculator gives the coefficients C0, C1 and C2, the outflow at the end of the step, the water stored and a time step check.

Example

A reach has K = 12 h and X = 0.2, routed with a step of 6 h. The coefficients are C0 = 0.0476, C1 = 0.4286 and C2 = 0.5238, and they add up to 1. With an inflow rising from 1,000 cfs to 1,800 cfs and an outflow of 900 cfs at the start, the outflow at the end of the step is O2 = C0 I2 + C1 I1 + C2 O1 = 985.7 cfs. The reach then holds 1,139.1 acre-ft.

Why it matters

The calculator helps hydrologists, drainage engineers and students to route a flood through a stream reach step by step, to see how a reach attenuates and delays a peak and to check that the time step they chose gives a stable and positive routing.

Good to know

Calibrate K and X on a measured flood where you can. Use a time step of about K, and make sure the step stays between 2KX and 2K(1 − X). Route the whole hydrograph by feeding each outflow back as the next previous outflow, and look at the peak, which should be lower and later than the inflow peak. Check that the volume out matches the volume in.

The Gumbel flood frequency calculator gives the design flow of a return period, the critical depth calculator finds the control depth of a channel, the hydraulic jump calculator gives the loss in a jump and the broad-crested weir calculator gives the flow over a weir.

Frequently asked questions

What is the Muskingum method?

The Muskingum method routes a flood wave through a channel reach with a storage equation, S = K [X I + (1 − X) O], where I is the inflow and O the outflow. K is the travel time of the wave through the reach and X weights the inflow against the outflow in the storage. Combined with the continuity equation, it gives the outflow at the end of a step from the two inflows and the previous outflow.

How are the coefficients found?

With the denominator D = K (1 − X) + 0.5 Δt, the coefficients are C0 = (0.5 Δt − K X) / D, C1 = (0.5 Δt + K X) / D and C2 = (K (1 − X) − 0.5 Δt) / D. They add up to 1. The outflow at the end of the step is O2 = C0 I2 + C1 I1 + C2 O1, so the routing of a whole flood is a repetition of this step, each outflow becoming the previous outflow of the next step.

How do I choose K, X and the time step?

K is close to the travel time of the peak through the reach, found from observed hydrographs or from the length divided by the wave speed. X is between 0 and 0.5, with about 0.2 for natural streams, 0 for a reservoir effect and 0.5 for no attenuation. The time step should be between 2KX and 2K(1 − X), and close to K or smaller, to keep the coefficients positive and the result smooth.

What are the limits of the method?

The method uses constant K and X, so it suits reaches without large changes of the flow with the stage, and it neglects the backwater and the inflow along the reach. It cannot model a dam or a tidal reach. For a steep flood in a wide flood plain, for a diffusion wave or for an important design, use a hydraulic model, and calibrate K and X with measured floods.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.