Skip to content
Omnikalc

Chip seal calculator: aggregate rate and emulsion rate for a surface treatment

Enter the aggregate size, the voids, the specific gravity, the traffic, the surface allowances, the residue of the emulsion and the area to get the aggregate rate, the emulsion rate and the totals.

Updated on
Your inputs
in

Value out of range

%

Value out of range

Value out of range

Value out of range

Value out of range

gal/yd²

Value out of range

gal/yd²

Value out of range

%

Value out of range

yd²

Value out of range

Results

Emulsion application rate

0.401 gal/yd²

Aggregate spread rate
27.3 lb/yd²
Total aggregate
136.4 tons
Total emulsion
4,006 gal

The chip seal calculator gives the aggregate spread rate, the emulsion application rate and the total quantities of a surface treatment with the method of McLeod, from the size and the voids of the aggregate, the traffic, the surface allowances and the residue of the emulsion.

How the calculation works

  • Enter the average least dimension of the aggregate, its voids in the loose state, its specific gravity and the waste factor.
  • Enter the traffic factor, the allowances for the surface condition and the absorption, the residual asphalt of the emulsion and the area.
  • The calculator finds the aggregate rate, the emulsion rate and the total quantities for the job.

Example

A chip seal uses an aggregate with an average least dimension of 0.25 in, 50 % of voids, a specific gravity of 2.65 and a waste factor of 1.10, so the aggregate rate is 46.8 × (1 − 0.4 × 0.5) × 0.25 × 2.65 × 1.10 = 27.3 lb/yd². With a traffic factor of 0.75, allowances of 0.03 and 0.02 gal/yd² and an emulsion with 65 % of residue, the emulsion rate is (2.244 × 0.25 × 0.75 × 0.5 + 0.03 + 0.02) / 0.65 = 0.401 gal/yd². On 10,000 yd², the job needs 136.4 tons of aggregate and about 4,006 gal of emulsion (computed with the unrounded rate).

Why it matters

The calculator helps road engineers, municipal crews, contractors and students to estimate the quantities of aggregate and emulsion to order for a chip seal, to see how the size of the aggregate and the traffic change the binder rate, and to compare the cost of several aggregates before the work.

Good to know

Use an aggregate that is clean, dry and uniform in size, and spread it right behind the spray bar before the emulsion breaks. Roll at once and sweep the loose stones after the cure. Calibrate the spray rate and the spread rate with a test strip, and adjust the binder on site for the surface condition, the temperature and the traffic. Close the road to a fast traffic until the binder has cured.

The asphalt paver production and trucks calculator sizes a paving crew, the flexible pavement ESAL capacity calculator checks the structure of a road, the driveway paving cost calculator estimates a small paving job and the pavement marking paint quantity calculator estimates the paint for the lines.

Frequently asked questions

What is a chip seal?

A chip seal is a surface treatment of a road made of a layer of bituminous binder, usually an emulsion, sprayed on the pavement and covered at once with a single layer of aggregate that is rolled. It seals the cracks, restores the skid resistance and extends the life of the pavement at a low cost. It is common on rural roads with a low or medium traffic.

How is the binder rate found?

The binder rate is found with the McLeod design method. The binder must fill a part of the voids between the stones, which depends on the thickness of the aggregate layer, the voids and the traffic, and the allowances for the surface condition and the absorption of the aggregate are added. The total is divided by the residue of the emulsion, to give the rate of the emulsion as sprayed.

What is the traffic factor?

The traffic factor is the part of the voids that the binder fills, which is lower for a heavy traffic and higher for a low traffic. A heavy traffic orients the stones and reduces the voids, and too much binder would bleed on the surface. The values go from about 0.6 for a heavy traffic to 0.85 for a very low one. The calculator takes 0.75 as a typical value for a medium traffic.

What are the limits of the calculator?

The calculator gives the design rates of the method with the inputs that you enter. It does not replace the lab tests of the gradation and the flakiness of the aggregate, or the trial section. The real rates depend on the temperature, the age and the roughness of the old surface, the type of emulsion and the equipment. The rates are adjusted on site and the spray bar must be calibrated before the work.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.