Skip to content
Omnikalc

Air receiver tank sizing calculator: volume in gallons for a peak air demand

Enter the peak air demand, its duration and the cut-in and cut-out pressures of the compressor to get the air receiver volume in cubic feet and gallons, with the rule-of-thumb size.

Updated on
Your inputs
scfm

Value out of range

s

Value out of range

psig

Value out of range

psig

Value out of range

Results

Recommended receiver size

264 gal

Receiver volume needed for the peak
35.3 ft³
Same volume in gallons
264 gal
Rule of thumb (3 gallons per scfm)
180 gal
Same volume in cubic feet
35.3 ft³

An air receiver is a tank that stores compressed air for the peaks of demand. The compressed air receiver calculator gives the volume needed to supply a peak of known flow and duration while the pressure drops between the cut-out and cut-in pressures of the compressor, with the rule-of-thumb size.

How the calculation works

  • Enter the peak air demand in standard cubic feet per minute (scfm) and the duration of the peak in seconds.
  • Enter the cut-out pressure (upper) and the cut-in pressure (lower) of the compressor, in psig.
  • The calculator gives the receiver volume that supplies the peak without the compressor: V = t × C × Pa / (P1 − P2), with Pa = 14.7 psi.
  • It compares the result with the rule of thumb of 3 gallons per scfm and gives the recommended size, the larger of the two.

Example

A machine needs 60 scfm for 60 s, and the compressor cuts out at 125 psig and cuts in at 100 psig. The receiver volume is 1 min × 60 scfm × 14.7 / 25 = 35.3 ft³, which is 264 gal. The rule of thumb gives 3 × 60 = 180 gal, so the recommended size is 264 gal, and a standard 300-gallon receiver would do.

Why it matters

The calculator helps workshop owners, plant engineers, installers and students to size or to check an air receiver, to understand the effect of the pressure band on the tank size and to choose a standard tank. A good size saves electricity by reducing the starts and the pressure losses.

Good to know

The calculator assumes an isothermal expansion of the air in the tank, a constant demand during the peak and that the compressor does not supply air during the peak, which is on the safe side. It does not include the pressure drop in the pipes and the dryers, the temperature changes or the compressor capacity control. Real tanks come in standard sizes, and they must follow the pressure vessel rules of your region.

The compression ratio calculator gives the ratio of a compressor, the gas compressibility factor calculator corrects the volume of real gases, the fan affinity laws calculator covers fans and blowers, and the pump power calculator covers the energy of liquid pumps.

Frequently asked questions

Why does a compressed air system need a receiver?

An air receiver is a tank that stores compressed air. It supplies short peaks of demand without starting the compressor, it reduces the cycling of the compressor, it dampens the pressure pulses and it lets the water and oil in the air condense and drain. A good receiver saves energy and extends the life of the compressor, and it prevents the pressure from dropping under the needs of the tools.

How is the receiver volume computed?

The receiver supplies the peak demand while the pressure falls from the cut-out pressure to the minimum pressure needed. The free air volume released is the receiver volume times the pressure drop divided by the atmospheric pressure, so V = C × t × Pa / (P1 − P2) with C the demand in free air per minute, t the time in minutes and Pa the atmospheric pressure. A narrow pressure band needs a larger tank.

What is the rule of thumb for the size?

A common rule of thumb for a receiver is about 3 to 4 gallons per scfm of the compressor capacity, or in metric units about 0.4 L per L/min of free air delivered. It is a good value for a general system. When the demand has large peaks, a bigger receiver or a second one near the point of use is better. The calculator gives the larger of the computed and the rule-of-thumb volume.

Can the receiver be too large?

A very large receiver costs more, takes space and needs more time to refill, but it does no harm to the operation, and it can help the compressor to run in longer and more efficient cycles. In some systems with a variable speed compressor the receiver can be smaller. The tank must have a safety valve, a drain and a pressure rating higher than the system pressure, and it must be inspected as required by local rules.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.