Skip to content
Omnikalc

Elastic settlement of a footing calculator: immediate settlement of a spread footing

Enter the net pressure, the footing width, the soil modulus, Poisson’s ratio and the footing shape to get the elastic settlement, its share of the width, the soil modulus needed for an allowable settlement and the margin.

Updated on
Your inputs
ksf

Value out of range

ft

Value out of range

ksf

Value out of range

Value out of range

in

Value out of range

Results

Elastic settlement

0.37 in

Settlement as a share of the footing width
0.52 %
Soil modulus needed for the allowable settlement
186.7 ksf
Allowable settlement over the computed settlement
2.68
Settlement is well within the allowable value

The elastic settlement of a footing calculator gives the immediate settlement of a spread footing from the net bearing pressure, the footing width, the soil modulus, Poisson’s ratio and the influence factor, and checks it against an allowable settlement.

How the calculation works

  • Enter the net bearing pressure under the footing and its width (or diameter for a round footing).
  • Enter the elastic modulus Es and Poisson’s ratio of the soil, and choose the shape and rigidity of the footing, which sets the influence factor Iw.
  • The calculator applies the elastic settlement equation Se = q B (1 − ν²) Iw / Es.
  • It gives the settlement, its share of the width, the modulus needed to meet your allowable settlement, and the margin.

Example

A 6 ft square flexible footing carries a net pressure of 3 ksf on a soil with Es = 500 ksf and ν = 0.3, with an influence factor of 0.95. The settlement is Se = 3 × 6 × (1 − 0.09) × 0.95 / 500 = 0.0311 ft, or 0.37 in, which is 0.52% of the width. To keep the settlement under 1 in, the soil needs a modulus of 186.7 ksf, and the margin is a factor of 2.68.

Why it matters

The calculator helps geotechnical and structural engineers, builders and students to estimate the settlement of a footing on sand or stiff clay, to check a design against a settlement limit and to see how much soil stiffness is needed. It is a first check before a detailed settlement analysis.

Good to know

Use a soil modulus from tests, and compare the result with a lower and upper estimate of Es. Add the consolidation settlement for clays under the water table. Check the differential settlement between footings, which often governs for a building. Verify the bearing capacity separately, because a low settlement does not guarantee a safe footing.

The consolidation settlement calculator covers soft clays, the footing size calculator sizes the footing, the Rankine earth pressure calculator covers retaining structures and the soil unit weight calculator converts the soil weight.

Frequently asked questions

What is elastic settlement?

Elastic settlement, also called immediate settlement, is the vertical movement of a footing that occurs as the load is applied, from the elastic deformation of the soil without any change in its water content. It is the main settlement in sands and in stiff clays above the water table, while consolidation settlement of soft saturated clays takes months or years and has to be added separately.

What is the influence factor Iw?

The influence factor depends on the shape of the loaded area, on how rigid the footing is, and on the point where the settlement is computed. A flexible footing settles more at the center than at the edge, and the average value is smaller. A rigid footing settles uniformly, with a value near the average of the flexible footing. Longer rectangular footings have higher factors, up to about 2 for a strip.

How do I choose the soil modulus?

Es is the hardest input. It comes from the plate load test, the pressuremeter, correlations with the SPT blow count or the cone penetration test, or from a lab triaxial test, and it increases with depth and confinement. Typical values are 150 to 1,000 ksf (7 to 50 MPa) for sand, and 50 to 500 ksf (2.5 to 25 MPa) for clay. A small error in Es gives an equally large error in the settlement.

What are the limits of the formula?

The formula assumes a homogeneous elastic half-space of infinite depth, so it fits best when the soil is uniform. For layered soils or a hard layer at a shallow depth, the settlement has to be computed by layers with a stress distribution method, or with the Schmertmann method for sands. Total settlements of 1 in (25 mm) and differential settlements of 3/4 in are typical limits for buildings.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.