Skip to content
Omnikalc

Erosion control blanket and staples calculator

Enter the slope height, the steepness, the length, the roll size, the overlap and the staples per square yard to get the area, the rolls and the staples.

Updated on
Your inputs
ft

Value out of range

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

%

Value out of range

Value out of range

Results

Rolls needed

8

Length of the slope face
31.62 ft
Area of the slope
6,008 ft²
Area to buy with the overlap
6,609 ft²
Staples needed
1,469

The erosion control blanket calculator gives the length of the slope face, the area, the area to buy with the overlap, the number of rolls and the number of staples for a slope, from its height, its steepness and its length.

How the calculation works

  • Enter the height of the slope, its steepness and its length along the contour.
  • Enter the width and length of a roll, the overlap and waste and the staples per square yard.
  • The calculator gives the slope length, the area, the area to buy, the number of rolls and the number of staples.

Example

A slope 10 ft high at 3:1 and 190 ft long has a face of 10 × √(3² + 1) = 31.62 ft and an area of 31.62 × 190 = 6,008 ft². With 10 % for overlap and waste you buy 6,609 ft². A roll of 8 × 112.5 ft covers 900 ft², so you need 6,609 / 900 = 7.34, that is 8 rolls. With 2 staples per square yard, 734.4 yd² need 1,469 staples.

Why it matters

The calculator helps site contractors, landscapers, erosion control inspectors and estimators to order the blanket and the staples for a slope or a bank, and to take the real area of the face, not the area seen from above.

Good to know

Roll the blanket down the slope, not across it, and lay it in contact with the soil without stretching it. Overlap the rolls in the direction of the water so that the upper roll is on top, and bury the top end in a trench. Order the staples with a few more than the count and keep the extra for repairs after the first storms.

The silt fence calculator counts the posts and the fabric at the toe of a slope, the hydroseeding calculator gives the slurry for the seed, the swale calculator sizes the channel and the geotextile filter calculator checks the filter criteria.

Frequently asked questions

How is the area of the slope found?

The area is the length of the slope face times the length along the contour. The slope face is longer than the horizontal run: for a slope of H horizontal to 1 vertical, it is the height times √(H² + 1). A 3:1 slope has a face 3.16 times its height. The calculator takes the slope height and not the plan area, which would understate the blanket by 5 % at 4:1 and 16 % at 2:1.

How much overlap and waste should I add?

The usual overlap between rolls is 2 to 4 in, and the blanket is also set in a trench at the top, at the toe and at intervals down a long slope. Together with the waste at the ends, this takes 10 to 15 % of the area. A slope with many angles or a cut roll at every end can need more. The calculator applies one percentage to the area, and you can raise it for a complex slope.

How many staples are needed?

The manufacturer gives the staple pattern, which depends on the steepness and the length of the slope: often 1.5 to 2 staples per square yard for a gentle slope, up to 3 or more for a steep slope or a channel, with more along the edges, the overlaps and the trenches. Use the pattern of the product and the specification, and enter its rate. Use longer staples in loose soil.

What does the calculator leave out?

The calculator does not count the seed, the mulch, the soil preparation or the trench excavation. It does not choose the type of blanket, which depends on the slope, the flow and the time of the cover: straw, coconut, a mix, or a permanent turf reinforcement mat. Grade and seed the slope first, and lay the blanket loose on the soil, not stretched.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.