Skip to content
Omnikalc

Flywheel sizing for speed fluctuation calculator

Enter the energy fluctuation, the mean speed, the allowed coefficient and the material to get the inertia needed and the size and the mass of a disc flywheel.

Updated on
Your inputs
J

Value out of range

rpm

Value out of range

Value out of range

mm

Value out of range

Results

Moment of inertia required

0.633 kg·m²

Diameter of the disc
379 mm
Mass of the disc
35.3 kg
Rim speed
23.8 m/s
Maximum speed
1,230 rpm
Minimum speed
1,170 rpm
Kinetic energy at the mean speed
5,000 J

The flywheel sizing calculator gives the moment of inertia needed, the diameter and the mass of a solid disc flywheel, its rim speed, the maximum and minimum speeds and the kinetic energy at the mean speed.

How the calculation works

  • Enter the energy fluctuation per cycle and the mean speed.
  • Enter the coefficient of speed fluctuation that your machine accepts.
  • Choose the material and the thickness of the disc to get its diameter and mass.

Example

To keep a fluctuation of 0.05 at 1200 rpm with 500 J per cycle, the flywheel needs 0.633 kg·m². A disc 40 mm thick has a diameter of 379 mm and a mass of 35.3 kg, with a rim speed of 23.8 m/s. The speed varies between 1,170 rpm and 1,230 rpm, and the disc holds 5,000 J at the mean speed.

Why it matters

The calculator helps designers of engines, presses, pumps, compressors and generators who need a flywheel to smooth the speed, and makers who size one for a single-cylinder engine or a machine with a pulsating load.

Good to know

The flywheel is sized on the energy fluctuation of the worst cycle, not on the mean power. A flywheel with the mass at the rim is more efficient than a disc, so if the size is limited, use a rim and spokes: the inertia of a ring of the same mass is twice that of a disc. Mount it on the fastest shaft. Do not forget the starting time: a heavy flywheel needs a stronger starter or a longer run-up. Check the rim speed and the stress, and balance the wheel, because a small imbalance at high speed creates large forces.

The flywheel energy calculator gives the energy stored and the runtime, the moment of inertia calculator handles other shapes, the slider-crank calculator gives the motion that creates the fluctuation and the piston speed calculator relates the speed to the engine.

Frequently asked questions

What is the coefficient of speed fluctuation?

The coefficient Cs is the difference between the maximum and the minimum speed divided by the mean speed. A pump or a press accepts 0.05 to 0.1, a machine tool 0.02 to 0.05, a generator 0.003 to 0.01 and a precision instrument 0.002 or less. The smaller the coefficient, the heavier the flywheel for the same energy fluctuation.

How is the inertia of the flywheel found?

The energy that the flywheel must absorb and return in one cycle is ΔE = I × ω² × Cs. So the inertia is I = ΔE / (ω² × Cs), with ω the mean angular speed in rad/s. For 500 J, 1 200 rpm (125.7 rad/s) and Cs = 0.05, the inertia is 0.633 kg·m². The inertia grows with the square of the lower speed, so it is cheaper to mount the flywheel on the faster shaft.

How do I find the energy fluctuation?

The energy fluctuation is the difference between the maximum and the minimum of the cumulated work of the torque over a cycle, that is the area between the torque curve and its mean. For a single-cylinder four-stroke engine it is about 3 to 4 times the work of one power stroke, and it is lower for engines with more cylinders. Use the area of your torque diagram or a measured value.

Does the rim speed have a limit?

Yes. The stress in a rotating disc grows with the square of the rim speed. Cast iron flywheels are kept under 30 to 40 m/s, steel flywheels under 60 to 100 m/s, and special composite wheels go much higher. The calculator shows the rim speed so that you can compare it with the limit of the material.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.