Skip to content
Omnikalc

Horizontal lifeline tension and anchor load calculator

Enter the span, the sag, the arresting force and the anchor rating to get the tension in a horizontal lifeline, the amplification of the force and the anchor strength required.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

lb

Value out of range

lb

Value out of range

Results

Anchor strength required

4,589 lb

Sine of the angle of the line
0.196
Tension in the lifeline
2,295 lb
Amplification of the arresting force
2.55
Rated strength to required strength
1.09
The anchors are strong enough for the tension in the line

The horizontal lifeline calculator gives the tension in a lifeline when a worker falls, the amplification of the arresting force and the anchor strength required for the span and the sag.

How the calculation works

  • Enter the span of the horizontal lifeline and the deflection of the line at midspan when a worker falls.
  • Enter the arresting force on the worker, the safety factor and the rated strength of each end anchor.
  • The calculator gives the tension in the line, the amplification of the force, the anchor strength required and the check of the anchors.

Example

A horizontal lifeline spans 40 ft and sags 4 ft at midspan when a worker with an arresting force of 900 lb falls. The half-span is 20 ft, so the sine of the angle of the line is 4 / √(20² + 4²) = 0.196. The tension is T = 900 / (2 × 0.196) = 2,295 lb, which is 2.55 times the arresting force. With a safety factor of 2, each anchor needs 4,589 lb, and anchors rated 5,000 lb give a ratio of 1.09.

Why it matters

The calculator helps safety managers, riggers, fall protection specialists and students to see why the anchors of a horizontal lifeline must be much stronger than those of a single-point anchor, and to compare spans and sags for a job.

Good to know

Use the deflection that the line really has when it is loaded, not the sag of the line at rest, since the deflection depends on the stretch of the line and the energy absorbers of the system. Use the maximum arresting force of the system, not the weight of the worker. Remember that the force is shared by both anchors, and that the structure behind the anchors must be as strong as the anchors. If the result is not acceptable, shorten the span, use a line with more stretch or an energy absorber, or accept more clearance below the worker. Follow the maker’s instructions and the rules of your jurisdiction.

The fall protection clearance calculator gives the free fall and the clearance below the worker, the climbing fall factor calculator gives the impact force of a rope, the lifting lug calculator checks a padeye and the guyed mast calculator gives the tension in guy cables.

Frequently asked questions

Why is the tension higher than the weight of the worker?

When a worker falls, the lifeline sags and the load is carried by the two halves of the line, which are almost horizontal. The vertical part of the tension is half of the load, but the line is nearly flat, so the tension along the line is much larger. A flatter line gives a larger amplification, which can be several times the arresting force.

What is the formula?

With the load at midspan, each half of the line makes an angle with the horizontal whose sine is sag / √((span / 2)² + sag²). The tension in the line is T = P / (2 sin θ), where P is the arresting force. The anchor must resist T multiplied by the safety factor, and in practice the end anchors, the line and the connectors each need to be checked.

What does a longer sag do?

A larger sag lowers the tension in the line and in the anchors, but it increases the fall distance and the clearance needed below the worker, because the line drops by the sag. Energy-absorbing lanyards and shock-absorbing devices at the ends reduce the peak force. The right choice balances the anchor loads with the clearance.

What does the calculator leave out?

The calculator leaves out the stretch of the line, the dynamics of the fall with its energy absorbers, a worker who falls near an end, the sag of the line under its own weight, multiple workers on the same line and the strength of the structure that holds the anchors. A horizontal lifeline system should be designed by a qualified person.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.