Skip to content
Omnikalc

Slope stability calculator: will the slope slide?

Enter the slope angle, the depth of the failure surface, the soil strength, the unit weight and the pore pressure ratio to get the factor of safety.

Updated on
Your inputs
°

Value out of range

ft

Value out of range

°

Value out of range

psf

Value out of range

pcf

Value out of range

Value out of range

Results

Factor of safety against sliding

1.29

Marginal: below the usual 1.5 target for a permanent slope
Shear stress driving the slide
286.3 psf
Shear strength along the failure surface
368.2 psf
Factor of safety if the slope were dry
1.59
Steepest angle of a dry, cohesionless slope
30 °

Hillsides, embankments and cuts are stable because the soil’s strength can resist the pull of gravity along a sliding surface. The infinite slope stability calculator takes the slope angle, the depth of the failure surface, the friction angle, the cohesion, the unit weight and the pore pressure ratio, and gives the factor of safety, the driving stress, the shear strength, the dry-slope factor of safety and the steepest dry cohesionless angle.

How the calculation works

  • Enter the slope angle and the depth of the possible sliding surface, parallel to the ground surface.
  • Enter the soil’s effective friction angle, effective cohesion and unit weight.
  • Enter the pore pressure ratio ru, which is the water pressure on the failure surface divided by the weight of the soil above it. Use 0 for a dry slope and about 0.2 to 0.5 for a wet one.
  • The driving stress is τ = γ × z × sin β × cos β, and the strength is s = c’ + (γ × z × cos²β − u) × tan φ’, with u = ru × γ × z. The factor of safety is s ÷ τ.

Example

A long slope has β = 25° with a possible failure surface 6.5 ft deep, in soil with φ’ = 30°, c’ = 100 psf, γ = 115 pcf and ru = 0.2. The driving stress is 115 × 6.5 × sin 25° × cos 25° = 286.3 psf. The effective normal stress is 115 × 6.5 × cos²25° − 0.2 × 115 × 6.5 = 614 − 150 = 464 psf, so the strength is 100 + 464 × tan 30° = 368.2 psf. The factor of safety is 368.2 ÷ 286.3 = 1.29, marginal against 1.5. If the slope were dry, it would rise to 1.59.

Why it matters

The same slope that stands in the dry season can fail after heavy rain, when water pressure builds in the soil. Changing ru in the calculator shows how much margin is lost to water, which explains why drainage matters so much for slopes, embankments and the cuts behind retaining walls.

Good to know

The infinite slope model is simple and gives a first look at shallow translational slides. It assumes a uniform soil, a failure surface parallel to the ground and a constant pore pressure ratio. Real hillsides need a site investigation. Do not rely on this tool for safety decisions about houses, roads or people below a slope.

The angle of repose calculator covers loose material, the soil loss calculator estimates erosion, the retaining wall calculator covers walls that hold a slope, and the drain slope calculator helps set the fall for drainage.

Frequently asked questions

What is the infinite slope method?

It is a simple analysis for a long slope where the failure surface is shallow and parallel to the ground surface, as in a sheet of soil sliding on rock or a hard layer. Because the slope is long, the ends do not matter and the forces on a slice can be worked out in one step.

What is the factor of safety?

It is the ratio of the shear strength of the soil along the failure surface to the shear stress needed for equilibrium. Above 1, the slope stands. Below 1, it slides. For permanent slopes, designers usually want at least 1.5, and for temporary ones 1.25 or more.

How does water change things?

Water pressure in the soil lowers the effective stress on the sliding surface and so the friction. The pore pressure ratio ru measures this. Seepage parallel to the slope with the water table at the surface gives an ru of about 0.4 to 0.5 for typical soils, which can roughly halve the factor of safety of a sandy slope.

What are the limits?

The method does not apply to deep rotational failures, to short slopes or to layered soils with weak zones at other depths. Vegetation, roots, earthquakes and loads at the top change the result. Do not use this alone to judge a hillside near a building, and have an engineer assess real slopes.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.