Skip to content
Omnikalc

Masonry lintel load calculator: size a steel lintel over an opening

Enter the span of an opening, the weight of the wall above, an added line load and the steel strength to get the triangular masonry load, the moment, the required section modulus, the stiffness for L/600 and the reactions.

Updated on
Your inputs
ft

Value out of range

psf

Value out of range

plf

Value out of range

ksi

Value out of range

Results

Required elastic section modulus Sx

1.05 in³

Weight of the masonry triangle on the lintel
720 lb
Maximum bending moment
2,070 lb-ft
Required moment of inertia Ix for a deflection of span / 600
3.80 in⁴
Reaction at each end
1,260 lb

A masonry lintel carries a triangle of masonry over an opening, thanks to the arching action, plus any added load. The masonry lintel load calculator computes the triangular load, the bending moment, the required section modulus, the stiffness for a deflection limit and the end reactions of a steel lintel.

How the calculation works

  • Enter the clear span of the opening, the weight of the wall above in pounds per square foot of wall face, and any added line load from a floor or roof that bears on the wall above the lintel.
  • Enter the yield strength of the steel lintel: 36 ksi for an ordinary angle or plate, 50 ksi for a modern section.
  • The calculator assumes arching action: only the masonry inside a triangle with a base equal to the span and a height of half the span loads the lintel, so W = ½ × L × (L/2) × wall weight. The triangular load has a moment of W L / 6, and the added load a moment of w L² / 8.
  • It gives the required section modulus for an allowable bending stress of 0.66 Fy, the moment of inertia for a deflection of span / 600 and the end reactions.

Example

An opening has a clear span of 6 ft in a wall that weighs 80 psf, with an added line load of 300 plf and a lintel of Fy = 36 ksi. The triangle of masonry weighs ½ × 6 × 3 × 80 = 720 lb. The moment is 720 × 6 / 6 + 300 × 6² / 8 = 720 + 1,350 = 2,070 lb-ft. The required section modulus is 2,070 × 12 / 1,000 / (0.66 × 36) = 1.05 in³. The moment of inertia for a deflection of L / 600 is 3.80 in⁴, and the reaction at each end is 360 + 900 = 1,260 lb.

Why it matters

The calculator helps masons, builders, home renovators, designers and students to size the steel angle or beam that spans a window, a door or a new opening in a brick or block wall, and to see how much the arching action reduces the load. It gives the numbers to compare with the properties of a section from a table.

Good to know

Support the lintel on at least 4 in (100 mm) of bearing at each end, and use a lintel with a flange or a plate for a thick wall to avoid twisting. Keep the deflection small to avoid cracks in the masonry. Leave the wall to cure before removing any temporary shoring. Have an engineer check a lintel that carries a floor or a roof.

The beam bearing length calculator checks the ends of the lintel, the wood beam span calculator sizes the wood version, the bricks calculator counts the units in the wall and the concrete block fill calculator covers the grout in the blocks.

Frequently asked questions

What is arching action?

Masonry over an opening acts like an arch. When the mortar has cured, the wall above the opening transfers most of its weight to the sides, and only a triangle of masonry loads the lintel. The triangle has a base equal to the span and its sides at 45 degrees, so its height is half the span. Masonry outside the triangle is carried by the piers beside the opening.

When does the arching action not apply?

The arching needs enough wall height above the opening, at least the half-span plus some masonry above the apex, and enough length on each side of the opening to resist the horizontal thrust. It does not apply if the wall is not cured, if there is another opening nearby above, or if a floor or roof load falls inside the triangle. In those cases, a full rectangular load is used on the lintel.

How are floor and roof loads handled?

A concentrated or distributed load that bears on the wall inside the triangle, or within a height equal to the span above the opening, goes to the lintel in full. The calculator adds it as a uniform line load, which is a simple and conservative assumption. Loads that bear above the apex of the triangle are generally spread by the masonry and can be ignored, but check the code for the exact rule.

What are the limits of this calculator?

It gives the bending of a simply supported lintel in steel, with the allowable stress of 0.66 Fy, and a deflection limit of span / 600 to protect the masonry from cracking. It does not check the shear, the web crippling, the lateral buckling of the angle, the bearing at the ends, the torsion of an angle that carries a one-sided load, or the connection to the wall. A structural engineer must complete the design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.