Skip to content
Omnikalc

Mass concrete temperature calculator: heat of hydration and thermal cracking risk

Enter the cement content, the heat of hydration, the unit weight, the section size and the placing and ambient temperatures to get the adiabatic rise, the peak core temperature and the core to surface differential.

Updated on
Your inputs
lb/yd³

Value out of range

cal/g

Value out of range

pcf

Value out of range

°F

Value out of range

°F

Value out of range

Results

Core to surface differential

28.9 °F

Differential within the 35 °F limit of ACI 207
Adiabatic temperature rise
56.6 °F
Temperature rise of the section
33.9 °F
Peak temperature at the core
98.9 °F
Peak below 158 °F (70 °C): no risk of delayed ettringite formation

The mass concrete temperature calculator gives the adiabatic temperature rise, the rise of the section, the peak temperature at the core and the differential between the core and the surface of a thick concrete element, from the cement content, the heat of hydration and the placing temperature.

How the calculation works

  • Enter the cementitious content, the heat of hydration of the cement and the unit weight of the concrete.
  • Choose the size of the section, which sets the share of the adiabatic rise that is reached, and enter the placing and ambient temperatures.
  • The calculator finds the adiabatic temperature rise, the rise of the section, the peak temperature at the core and the differential between the core and the surface.

Example

A concrete with 350 lb/yd³ of cementitious material and a heat of hydration of 80 cal/g (144 BTU/lb) weighs 150 pcf. The adiabatic rise is 350 × 144 / (150 × 27 × 0.22) = 56.6 °F. For a section of about 5 ft (factor 0.6), the rise is 33.9 °F. With a placing temperature of 65 °F, the peak at the core is 98.9 °F, and with an ambient temperature of 70 °F the differential is 28.9 °F, below the 35 °F limit.

Why it matters

The calculator helps concrete engineers, contractors, quality managers and students to estimate the heat of a large pour such as a footing, a mat or a dam, to see the effect of the cement content and of the placing temperature and to decide if a thermal control plan is needed.

Good to know

Reduce the cement content with fly ash or slag, cool the aggregates and the mixing water, place the concrete at a low temperature and use insulation to keep the surface warm. Install temperature sensors in the core and near the surface, and keep a record until the differential falls.

The concrete curing calculator helps to plan the curing, the concrete volume calculator gives the volume of the pour, the concrete crack width calculator checks the cracks and the bridge expansion joint movement calculator shows the thermal movements.

Frequently asked questions

Why is the temperature important in mass concrete?

The hydration of the cement releases heat. In a thick element, the heat can not escape quickly, so the core gets hot while the surface cools to the air. The difference of temperature creates tensile stresses at the surface, which can crack the concrete. A very high peak temperature, above about 158 °F (70 °C), can also cause a delayed ettringite formation, which makes the concrete expand and crack months or years later.

How is the adiabatic rise found?

The adiabatic rise is the temperature rise if no heat is lost. It is the heat released by the cement per unit volume divided by the heat capacity of the concrete: ΔT = C H / (ρ c), with C the cementitious content, H the heat of hydration, ρ the unit weight and c the specific heat, about 0.22 BTU/lb·°F (0.92 kJ/kg·K). The real rise is lower because of the loss of heat at the surfaces, which is represented here by the section factor.

What are the limits of temperature?

ACI 207 recommends that the difference between the core and the surface does not exceed about 35 °F (20 °C), to avoid the thermal cracking, and many specifications limit the peak temperature to 158 °F (70 °C). The usual measures are to use a cement of low heat or a blend with fly ash or slag, to cool the materials or to use ice, to place the concrete in lifts and to insulate the surfaces.

What are the limits of the calculator?

The calculator gives a simple estimate with a section factor. It does not include the real heat curve in time, the heat loss by the formwork, the thermal properties of the foundation, the effect of the water–cement ratio or the pozzolans in detail, the cooling pipes or the thermal stress analysis. Mass concrete needs a thermal control plan by an experienced engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.