Skip to content
Omnikalc

Mobile crane outrigger reaction and float size calculator

Enter the crane weight, the lifted load, the radius, the boom angle, the outrigger spread and the ground pressure to get the outrigger reactions and the float size.

Updated on
Your inputs
lb

Value out of range

lb

Value out of range

ft

Value out of range

°

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

psf

Value out of range

Results

Largest outrigger reaction

42,883 lb

Average load on an outrigger
30,500 lb
Smallest outrigger reaction
18,117 lb
Smallest to average reaction
0.59
All four outriggers stay loaded
Bearing pressure to allowable pressure
0.89
Close to the allowable pressure: use a larger mat
Side of the float needed for the allowable pressure
3.78 ft

The mobile crane outrigger calculator gives the reaction of each outrigger under a lifted load, the tipping margin, the bearing pressure under the float and the float size for the ground.

How the calculation works

  • Enter the weight of the crane, the lifted load and its radius, and the angle of the boom from the long axis of the crane.
  • Enter the outrigger spread along and across the crane, the side of the float and the allowable ground pressure.
  • The calculator gives the largest and smallest outrigger reactions, the bearing pressure and the float side needed.

Example

A mobile crane of 110,000 lb lifts 12,000 lb at a radius of 30 ft, with the boom 25° from the long axis. The outriggers are 20 ft apart along the crane and 18 ft across, and each rests on a 4 ft square mat on ground that can take 3,000 psf. The average load is 30,500 lb per outrigger. The load adds 12,383 lb to the most loaded outrigger, which carries 42,883 lb, and the least loaded carries 18,117 lb, 0.59 of the average. The pressure under the mat is 0.89 of the allowable pressure, and a mat of 3.78 ft per side would be exactly enough.

Why it matters

The calculator helps lift planners, crane operators, site engineers and students to see how the load at a radius and a boom angle is shared by the outriggers, to size the mats on weak ground and to spot a lift that is near the tipping limit.

Good to know

Use the full outrigger spread and level the crane before the lift. Put the mats on firm, compacted ground and extend them in a way that spreads the largest reaction, with timber or steel mats of stiffness. Use the largest reaction of the worst boom position to size the mats, add the dynamic factor of your standard and keep the load close to the crane. Never lift near the tipping limit without the crane chart.

The crane mat bearing pressure calculator checks a mat on the ground, the crane lift utilization calculator adds the wind, the tower crane calculator balances the load moment and the tandem crane lift calculator shares a load between two cranes.

Frequently asked questions

How are the outrigger reactions found?

The weight of the crane is shared equally by the four outriggers, which gives the average load. The lifted load, at its radius from the center of rotation, adds an overturning moment that is resisted by the difference between the outriggers. With the boom at an angle, the moment about the long axis and about the cross axis are found separately and each is divided by twice the spread, then added to or subtracted from the average load.

When does a crane tip?

A crane tips when the smallest outrigger reaction falls to zero, because the outrigger on the side opposite the load lifts off. The calculator shows the ratio of the smallest reaction to the average one, and it is a warning when this ratio is small. Crane charts are based on a margin below the tipping limit, usually 85 % of the tipping load on outriggers, and the chart must be used for the actual configuration.

Where is the boom worst placed?

Over the corner, the reaction of the front outrigger is the largest, because the moment about both axes adds. Over the side or over the rear, the load is carried differently, and the crane chart gives the capacity for each position. Run the calculator for several boom angles to find the worst reaction before a lift, and use the largest value for the mat.

What does the calculator leave out?

The calculator takes the center of gravity of the crane at the center of the outriggers and treats the lifted load as static. It leaves out the dynamic effect of hoisting and swinging, the wind on the load and the boom, the slope of the ground, the soft ground and the rigidity of the mat. Use the crane chart and the engineer of the lift for the real capacity, and apply the usual load factors.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.