Skip to content
Omnikalc

Permeation grout take per hole calculator for soil injection

Enter the area, the depth, the hole spacing, the porosity, the part of the voids filled and the loss to get the number of holes, the total grout and the take per hole.

Updated on
Your inputs
ft²

Value out of range

ft

Value out of range

ft

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Results

Total grout volume

16,589 gal

Number of injection holes
38
Volume of soil treated
266.7 yd³
Grout take per hole
436.5 gal/hole
Grout take per foot of hole
36.4 gal/ft

The permeation grout take per hole calculator gives the number of injection holes, the volume of soil treated, the total grout volume and the grout take per hole and per foot of a permeation grouting, from the area, the depth, the spacing, the porosity and the part of the voids filled.

How the calculation works

  • Enter the area, the depth and the spacing of the injection holes.
  • Enter the porosity of the soil, the part of the voids that the grout fills and the loss of grout.
  • The calculator finds the number of holes, the volume of soil, the total grout and the grout take per hole and per foot.

Example

A block of 600 ft² and 12 ft deep is injected with holes at 4 ft, which makes ceil(600 / 16) = 38 holes. The treated soil is 600 × 12 / 27 = 266.7 yd³. With a porosity of 35 %, 80 % of the voids filled and 10 % of loss, the grout is 7,200 × 0.35 × 0.8 × 1.1 = 2,217.6 ft³, that is 16,589 gal. That is 436.5 gal per hole, or 36.4 gal per foot of hole.

Why it matters

The calculator helps geotechnical engineers, grouting contractors, estimators and students to estimate the quantity of grout of a soil injection, to compare the spacings of the holes and to plan the volumes of each stage of the injection and of the batching.

Good to know

Do a trial injection in a test area to check the pressure, the volume and the radius of the grout before the production. Inject by stages from the bottom up or from the top down, record the pressure and the volume of each stage, and stop when the pressure rises sharply or when the soil starts to heave. Keep a reserve of grout and mix it in small batches.

The stone column calculator gives the replacement ratio of another ground improvement, the soil compaction calculator checks the density of a fill, the ground anchor bond length calculator sizes a tieback and the trench dewatering calculator sizes the pumping of an excavation.

Frequently asked questions

What is permeation grouting?

Permeation grouting is the injection of a low-viscosity grout, like a chemical grout or a micro-fine cement, into the pores of a soil without changing its structure. The grout fills the voids between the grains and sets, which makes the soil stronger and less permeable. It works well in sands and gravels, and it is not effective in clays and silts, whose pores are too small for the grout.

How is the grout take estimated?

The take is the volume of the soil, times the porosity, times the part of the voids that the grout really fills, plus the loss. The porosity of a sand is about 30 to 40 %. The part of the voids filled is below 100 %, because the grout does not displace all the water and the air, and it depends on the viscosity of the grout and on the pressure of the injection.

How is the spacing of the holes chosen?

The holes are spaced so that the zones of the grout overlap. The radius of the zone depends on the permeability of the soil, on the viscosity and the gel time of the grout, on the pressure and on the volume injected in each stage. A wide spacing saves the holes, but it risks to leave untreated zones. The spacing is checked with a trial injection and the monitoring of the pressure and of the volume.

What are the limits of the calculator?

The calculator is a first estimate with simple parameters. It does not model the flow of the grout in the soil, the radius of the permeation, the fracturing of the ground with a pressure that is too high, the layers of different permeability, the dilution by the groundwater or the gel time of the grout. The injection must be designed and monitored by a specialist.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.