Skip to content
Omnikalc

Petroff journal bearing friction calculator: friction in a lubricated shaft bearing

Enter the oil viscosity, the speed, the journal size, the clearance and the load of a journal bearing to get the friction torque, the coefficient of friction, the power lost, the bearing pressure and the Sommerfeld number.

Updated on
Your inputs
µreyn

Value out of range

rpm

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

lb

Value out of range

Results

Friction torque T = 4π² µ N r³ L / c

9.47 lb-in

Coefficient of friction f = T / (W r)
0.0189
Power lost in friction
0.271 hp
Bearing pressure P = W / (2 r L)
125.0 psi
Sommerfeld number S = (r / c)² µ N / P
0.960

Petroff’s equation gives the friction of a lubricated journal bearing with a concentric shaft. The Petroff journal bearing friction calculator finds the friction torque, the coefficient of friction, the power lost, the bearing pressure and the Sommerfeld number from the oil, the speed, the geometry and the load.

How the calculation works

  • Enter the viscosity of the oil at the working temperature (in microreyns, 1 reyn = 1 lb·s/in²), the speed of the shaft, the radius and length of the journal, the radial clearance and the load.
  • The calculator applies Petroff’s equation for a lightly loaded journal bearing with a concentric shaft: the oil film is sheared like a simple fluid between two surfaces, so T = 4π² µ N r³ L / c, where N is in revolutions per second.
  • From the torque it finds the coefficient of friction f = T / (W r), the power lost in the film, the bearing pressure and the Sommerfeld number S, the dimensionless group that governs the behavior of the bearing.
  • Typical values: viscosity 2 to 8 µreyn for engine oils, a clearance ratio c / r of 0.001, and a Sommerfeld number from 0.05 to 1.

Example

A journal of 1 in radius and 2 in length turns at 1,800 rpm (30 rev/s) in oil of 4 µreyn, with a radial clearance of 0.001 in and a load of 500 lb. The friction torque is 4π² × 4×10⁻⁶ × 30 × 1³ × 2 / 0.001 = 9.47 lb-in. The coefficient of friction is 9.47 / (500 × 1) = 0.0189. The power lost is 0.271 hp. The bearing pressure is 500 / (2 × 1 × 2) = 125.0 psi and the Sommerfeld number is 0.960.

Why it matters

The calculator helps mechanical engineers, designers of engines, pumps and gearboxes, maintenance engineers and students to estimate the friction loss of a sleeve bearing, to compute the heat that the oil must carry away, and to see the effect of the viscosity, the clearance and the speed. It is the simplest model of hydrodynamic lubrication.

Good to know

Use the viscosity at the working temperature of the film, which is often 20 to 40 °C above the oil inlet. Keep a clearance ratio c / r of about 0.001. Check that the bearing pressure stays within the limits for the bearing material. For a heavier load, confirm the result with the charts of Raimondi and Boyd.

The bearing life calculator covers rolling bearings, the shaft torsion calculator gives the twist under the torque, the motor speed calculator links the frequency and the rpm and the Reynolds number calculator shows the flow regime of the oil.

Frequently asked questions

What is Petroff’s equation?

Petroff’s equation, from 1883, is the first theory of the friction in a lubricated journal bearing. It assumes a shaft that is concentric with the bearing, so the oil film has a uniform thickness equal to the radial clearance, and that the oil is sheared as in a simple fluid between two plates: the shear stress is µ U / c. Multiplying by the area and the radius gives the torque T = 4π² µ N r³ L / c.

What is the Sommerfeld number?

The Sommerfeld number S = (r / c)² µ N / P groups the viscosity, the speed, the pressure and the geometry in one dimensionless number. For a given bearing geometry, it determines the position of the shaft in the clearance, the thickness of the minimum film and the friction. Petroff’s equation can be written f = 2π² (r / c) (µ N / P), which is 2π² times the Sommerfeld number divided by the ratio r / c.

When is the equation accurate?

It is accurate for a lightly loaded bearing, in which the shaft runs almost concentric, which means a large Sommerfeld number: a high speed, a viscous oil and a light load. For a heavily loaded bearing, the shaft runs off-center, the film is thinner at one point and the friction is higher than Petroff’s value. Then use the Raimondi and Boyd charts or a numerical analysis.

What are the limits of the calculator?

It does not include the temperature rise of the oil, which lowers the viscosity, the end leakage of the oil, the misalignment of the shaft, or the start-up with a boundary lubrication. The viscosity must be taken at the temperature of the film, not that of the sump. Use the result as a first estimate of the friction and the heat to remove, and verify it with the bearing manufacturer for a critical machine.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.