Skip to content
Omnikalc

Pile downdrag calculator: negative skin friction force on a pile

Enter the pile diameter, the length in the settling soil, the effective stress, the beta factor, the sustained load, the ultimate capacity and the factor of safety to get the downdrag, the total load and the ratio to the allowable load.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

psf

Value out of range

Value out of range

kips

Value out of range

kips

Value out of range

Value out of range

Results

Load to allowable load ratio

0.85

Total load within the allowable load
Downdrag force (negative skin friction)
49.5 kips
Total load on the pile
169.5 kips
Allowable load
200.0 kips

The pile downdrag calculator gives the downdrag force (negative skin friction) on a pile in a soil that settles, the total load, the allowable load and the ratio between them, by the beta method, from the pile size, the effective stress and the loads.

How the calculation works

  • Enter the diameter of the pile and its length in the soil that settles, above the neutral plane.
  • Enter the average effective vertical stress along that length and the beta factor of the soil.
  • Enter the sustained design load, the ultimate capacity below the neutral plane and the factor of safety. The calculator finds the downdrag force, the total load, the allowable load and their ratio.

Example

A pile of 14 in goes through 30 ft of soft clay that settles under a new fill, with an average effective stress of 1,800 psf and β = 0.25. The downdrag is π × 14 / 12 × 30 × 0.25 × 1,800 / 1000 = 49.5 kips. With a sustained load of 120 kips, the total load is 169.5 kips. The ultimate capacity of 400 kips with a safety factor of 2 gives an allowable load of 200 kips, so the ratio is 169.5 / 200 = 0.85.

Why it matters

The calculator helps geotechnical and structural engineers, foundation contractors and students to evaluate the extra load of the downdrag in a preliminary design of piles through soft clay under a fill, and to compare options such as a coating or a longer pile.

Good to know

Estimate the settlement of the soil with a consolidation analysis, find the neutral plane, and check both the structural capacity of the pile and the settlement of the pile with the drag load. Use a conservative beta, and monitor the settlements if possible.

The pile capacity calculator gives the geotechnical capacity, the drilled shaft capacity calculator does the same for shafts, the pile group efficiency calculator checks the group and the consolidation settlement calculator gives the settlement of the soil.

Frequently asked questions

What is downdrag on a pile?

Downdrag, or negative skin friction, is a downward drag on a pile caused by a soil that settles more than the pile, for example a soft clay under a new fill, a lowering of the water table or a heavy surcharge. It adds a load to the pile, in the opposite direction of the usual shaft resistance, until the neutral plane is reached below which the pile settles more than the soil. It does not reduce the geotechnical capacity, but it increases the load and the settlement.

How is the downdrag force found?

The calculator uses the beta method of the effective stress, Qn = π D Ln β σ'v, with the pile perimeter, the length of the pile in the settling layers, the beta factor and the average effective vertical stress. Beta is often 0.2 to 0.3 for clays and 0.25 to 0.35 for silts. The total load is the sustained load plus the downdrag, and live loads are not added, because they are temporary and do not occur at the same time.

How can the downdrag be reduced?

The usual measures are to coat the pile with a bitumen layer or a plastic sleeve in the settling zone, to use a smaller perimeter, to install the piles after the settlement is done by preloading, to limit the surcharge of the fill, or to increase the structural capacity of the pile. Bitumen coatings can reduce the shaft friction in the settling zone by 80 to 90 %.

What are the limits of the calculator?

The calculator gives a simple estimate with a constant beta and an effective stress, which is the hypothesis of the beta method. It does not find the neutral plane by the equilibrium of loads and settlements, the group effect, the drag on batter piles or the effect of the time. Pile design in settling soils must be done by a geotechnical engineer, with a check of the structural capacity.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.