Skip to content
Omnikalc

Pile axial capacity calculator (alpha method): shaft resistance, end bearing and allowable load

Enter the diameter and length of a pile, the undrained shear strength of the clay, the adhesion factor and the factor of safety to get the shaft resistance, the end bearing and the allowable capacity.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

psf

Value out of range

Value out of range

Value out of range

Results

Allowable pile capacity

71.7 kips

Shaft (skin) resistance
155.5 kips
End bearing resistance
23.9 kips
Ultimate capacity
179.4 kips
Share of the load carried by the shaft
87 %

The axial capacity of a pile in clay comes from the friction on its sides and the bearing of its tip. The pile capacity calculator uses the alpha method with the undrained shear strength of the clay to give the shaft resistance, the end bearing, the ultimate capacity and the allowable load.

How the calculation works

  • Enter the diameter of the pile and its embedded length in the clay.
  • Enter the undrained shear strength of the clay, from the soil report, and the adhesion factor α (about 1.0 for soft clay and 0.5 for stiff clay).
  • The calculator computes the shaft resistance α × su × perimeter × length and the end bearing 9 × su × area of the tip.
  • It adds them into the ultimate capacity and divides by the factor of safety to give the allowable capacity.

Example

A pile of 18 in diameter is driven 40 ft into a clay with su = 1,500 psf and α = 0.55. The perimeter is 4.71 ft, so the shaft resistance is 0.55 × 1,500 × 4.71 × 40 = 155.5 kips. The tip area is 1.77 ft², so the end bearing is 9 × 1,500 × 1.77 = 23.9 kips. The ultimate capacity is 179.4 kips, of which 87 % comes from the shaft, and with a factor of safety of 2.5 the allowable capacity is 71.7 kips.

Why it matters

The calculator helps civil engineering students, foundation contractors and engineers to get a first estimate of the length or the diameter of a driven or bored pile in clay, to see how much of the load is carried by the shaft and by the tip and to compare options before the geotechnical design.

Good to know

The calculator gives a static estimate for a single pile in homogeneous clay under compression. It does not consider layered soils, group effects, negative skin friction, settlement, lateral loads, uplift, the strength of the pile itself or the local code. The adhesion factor and the strength must come from a soil investigation. Use the result for a first estimate only.

The bearing capacity calculator covers shallow footings, the retaining wall calculator checks a wall against sliding and overturning, the punching shear calculator checks a slab around a column, and the section modulus calculator is used to check the pile or beam section.

Frequently asked questions

How does a pile carry its load in clay?

A pile in clay carries the load by two ways: the friction or adhesion between the soil and the sides of the pile (the shaft resistance), and the bearing of the soil under the tip (the end bearing). In a long pile in soft clay, most of the load goes by the shaft. The sum of the two is the ultimate capacity, and the allowable load is the ultimate capacity divided by a factor of safety, usually between 2 and 3.

What is the alpha method?

The alpha method is a total stress method for piles in clay. The unit shaft adhesion is α times the undrained shear strength su of the clay. The factor α is less than 1, and it decreases as the strength of the clay increases, from about 1.0 for very soft clay to about 0.5 for stiff clay. The end bearing is Nc × su, with Nc about 9 for a deep foundation in clay.

Does this apply to sand?

No. In sand, the shaft resistance depends on the effective stress and on the friction angle (the beta method), and the end bearing depends on the bearing capacity factor Nq and on the vertical stress at the tip. The calculator is for cohesive soils only, and a pile in layered ground needs a calculation layer by layer. A geotechnical engineer must choose the method for the real soil.

Why is a pile load test still needed?

Calculated capacities are estimates, and the real value depends on the installation method, on the disturbance of the soil, on the time after driving (set-up) and on the layers of the ground. A static load test or a dynamic test on a sample of piles confirms the capacity and often allows a lower factor of safety. The calculator is for a first estimate and not for the final design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.