Skip to content
Omnikalc

Pile group efficiency calculator: how much capacity a pile group loses to interaction

Enter the number of rows and piles, the pile diameter and spacing and the capacity of a single pile to get the Converse-Labarre efficiency and the capacity of the group.

Updated on
Your inputs

Value out of range

Value out of range

in

Value out of range

in

Value out of range

kips

Value out of range

Results

Group efficiency (Converse-Labarre)

0.727

Noticeable group effect

Capacity of the group

654 kips

Number of piles in the group
9
Spacing as a multiple of the diameter
3.00 ×d
Spacing of at least 2.5 diameters
Angle θ = atan(d / s)
18.43 °

Piles placed close together interfere with one another. The pile group efficiency calculator uses the Converse-Labarre equation to give the efficiency of the group from the number of piles, their diameter and spacing, and the capacity of the group from the capacity of a single pile.

How the calculation works

  • Enter the layout of the group: the number of rows and the number of piles in each row.
  • Enter the diameter of the piles and their center-to-center spacing. The usual minimum spacing is 2.5 diameters, and 3 diameters is common.
  • Enter the capacity of a single isolated pile, from the static analysis or from a load test.
  • The calculator applies the Converse-Labarre equation Eg = 1 − θ [(n − 1) m + (m − 1) n] / (90 m n), with θ = arctan(d / s) in degrees, and multiplies by the number of piles and the single pile capacity.

Example

A group of 3 rows by 3 piles has piles of 12 in of diameter at 36 in spacing, which is 3 diameters. The angle is θ = arctan(12 / 36) = 18.43°. The efficiency is 1 − 18.43 × (2 × 3 + 2 × 3) / (90 × 3 × 3) = 0.727. With 100 kips per single pile, the group capacity is 0.727 × 9 × 100 = 654 kips, instead of 900 kips if the piles did not interfere.

Why it matters

The calculator helps foundation engineers, contractors and students to see how much capacity is lost when piles are packed closely, to compare layouts with different spacings and to choose the number of piles for a column load. It shows the value of a wider spacing.

Good to know

Keep the spacing at 2.5 to 3 diameters or more for friction piles. Check the capacity of the block failure of the group in clay. Remember that the group settlement is larger than that of one pile. Use the efficiency only for friction piles, and use 1 for end-bearing piles at a normal spacing.

The pile capacity calculator gives the capacity of a single pile, the bearing capacity calculator covers shallow foundations, the footing size calculator sizes the pile cap and the consolidation settlement calculator estimates the settlement of the clay.

Frequently asked questions

Why is a pile group weaker than its piles?

When piles are close together, the stress zones around them in the soil overlap. In friction piles in clay, the group can fail as a block, with the soil between the piles moving with them, and the capacity is smaller than the sum of the single piles. The settlement of the group is also larger than that of one pile with the same load per pile, since the load goes deeper into the soil.

What is the Converse-Labarre equation?

It is an empirical formula for the efficiency of a group of m rows and n piles in a row: Eg = 1 − θ [(n − 1) m + (m − 1) n] / (90 m n), where θ = arctan(d / s) in degrees, d is the diameter and s is the spacing. The efficiency is lower for a closer spacing and for a larger group. It is a simple way to account for the group effect in friction piles.

Does it apply to all piles?

Not to all. For end-bearing piles that go through to rock or to a very dense layer, the group effect is small, and the efficiency is generally taken as 1 for a spacing of at least 2.5 diameters. The group effect matters for friction piles in clay and in loose sand. In dense sand, driven piles can even get a higher capacity in a group because of the compaction of the soil between them.

What are the limits of this calculator?

The equation is empirical and it is a rough guide, not a rule of the codes. It does not include the block failure, which must be checked for a group in clay as the capacity of a block of soil, the settlement of the group, the lateral loads and the moments or the effect of the pile cap. For a real project, the geotechnical engineer must choose the method for the soil conditions.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.