Skip to content
Omnikalc

Drilled shaft capacity calculator: axial capacity of a bored pile in clay (FHWA alpha method)

Enter the diameter and length of the shaft, the undrained shear strength along the shaft and at the base, the safety factor and the load to get the side resistance, the end bearing, the ultimate and allowable capacity and the ratio.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ksf

Value out of range

ksf

Value out of range

Value out of range

kips

Value out of range

Results

Allowable capacity

175.9 kips

Side resistance
248.8 kips
End bearing
190.9 kips
Ultimate capacity
439.7 kips
Load over allowable capacity
0.85
The allowable capacity is above the load

The drilled shaft capacity calculator gives the axial capacity of a bored pile in clay with the alpha method of the FHWA: the side resistance, the end bearing, the ultimate and the allowable capacity, from the diameter, the length and the undrained shear strength.

How the calculation works

  • Enter the diameter and the length of the drilled shaft.
  • Enter the undrained shear strength of the clay along the shaft and at the base, from the soil report.
  • Enter the safety factor and the service load of the shaft.
  • The calculator finds the side resistance (alpha method, α = 0.55, neglecting the top 5 ft and the bottom diameter), the end bearing (Nc = 9), the ultimate and allowable capacity and the ratio to the load.

Example

A shaft of 3 ft of diameter and 40 ft of length is in a clay with 1.5 ksf along the shaft and 3.0 ksf at the base. The side resistance is 0.55 × 1.5 × π × 3 × (40 − 5 − 3) = 248.8 kips, and the end bearing is 9 × 3.0 × π × 3² / 4 = 190.9 kips. The ultimate capacity is 439.7 kips, which is 175.9 kips with a safety factor of 2.5. A service load of 150 kips is 0.85 of it.

Why it matters

The calculator helps geotechnical and structural engineers, foundation contractors and students to size a drilled shaft in a first design, to compare the diameter and the length and to see the share of the side resistance and of the end bearing. It reproduces the classic hand calculation for a shaft in clay.

Good to know

Use values of su from laboratory tests or in situ tests at the depth of each layer, and neglect the top of the shaft where the soil is disturbed. Make the safety factor at least 2.5, or use the resistance factors of the LRFD method. Check the settlement and the lateral loads, and verify the shaft on site with load tests.

The pile capacity calculator covers driven piles, the bearing capacity calculator covers shallow foundations, the pile group efficiency calculator covers groups of piles and the soil unit weight calculator converts the soil density.

Frequently asked questions

What is a drilled shaft?

A drilled shaft, also called a bored pile or a caisson, is a deep foundation made by drilling a cylindrical hole in the ground, placing a reinforcement cage and filling it with concrete. It is used for heavy loads, for bridges and tall buildings, and where driving a pile would cause vibrations or is not possible. The shaft carries the load by friction along its side and by the bearing at its base.

What is the alpha method?

In a clay under undrained conditions, the unit side resistance is a fraction α of the undrained shear strength su. The FHWA method of GEC-10 uses α = 0.55 when su divided by the atmospheric pressure is less than 1.5, and a lower value for stiffer clays. The top 5 ft of the shaft, where the soil is disturbed by the seasonal changes, and the bottom of one diameter, where the soil is affected by the base, are neglected.

How is the end bearing found?

The unit end bearing in a clay is qb = Nc su with Nc = 9 for a shaft with a length of more than four diameters. The end bearing is this value multiplied by the area of the base. It develops only after a settlement of 2 to 5% of the diameter, while the side resistance develops with less than 1%, so a safety factor on the total is a simplification of the design.

What are the limits of the calculator?

The calculator treats a single clay layer with constant su, in undrained conditions. It does not cover sand, rock, layered profiles, belled shafts, the settlement, the lateral loads, the group effect or the negative skin friction. The values of su must come from a geotechnical investigation, and the design of a drilled shaft must be made by a geotechnical engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.