Skip to content
Omnikalc

Plastic moment capacity calculator: Zx, Sx and the plastic moment of a steel I-beam

Enter the depth, the flange and the web of a steel I-shape and its yield strength to get the plastic and elastic section moduli, the shape factor, the plastic moment, the yield moment and the design plastic moment.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

ksi

Value out of range

Results

Plastic section modulus Zx

71.91 in³

Elastic section modulus Sx
63.77 in³
Shape factor Zx / Sx
1.128
Plastic moment Mp = Fy Zx
299.6 kip-ft
Yield moment My = Fy Sx
265.7 kip-ft
Design plastic moment φMp (φ = 0.90)
269.7 kip-ft

The plastic moment is the bending strength of a steel section when it has fully yielded. The plastic moment capacity calculator finds the plastic and elastic section moduli of an I-shape, the shape factor, the plastic moment, the yield moment and the design moment.

How the calculation works

  • Enter the dimensions of the doubly symmetric I-shape: the overall depth, the flange width, the flange thickness and the web thickness, as given by the section tables, and the yield strength.
  • The calculator computes the elastic section modulus Sx = I / (d / 2), from the moment of inertia of the I-shape.
  • It computes the plastic section modulus Zx = bf tf (d − tf) + tw (d − 2 tf)² / 4, the first moment of the area on each side of the plastic neutral axis, which is the center line for a symmetric shape.
  • The plastic moment is Mp = Fy Zx, the moment when the whole section yields. The shape factor Zx / Sx tells how much strength the section keeps after the first yield.

Example

A wide-flange shape has a depth of 16.0 in, a flange of 7.0 × 0.505 in, a web of 0.305 in and a yield strength of 50 ksi. The web height is 14.99 in. The elastic section modulus is 63.77 in³, and the plastic section modulus is 7 × 0.505 × 15.495 + 0.305 × 14.99² / 4 = 71.91 in³. The shape factor is 1.128. The plastic moment is 50 × 71.91 / 12 = 299.6 kip-ft, against a yield moment of 265.7 kip-ft, and the design plastic moment is 269.7 kip-ft.

Why it matters

The calculator helps structural engineers, steel designers and students to check the table values of Zx and Sx, to compute a built-up or custom I-shape, to estimate the flexural strength of a compact beam and to understand the reserve of strength beyond the first yield. It is the basis of plastic analysis and design.

Good to know

Compare your result with the tabulated Zx of the standard section: a difference of 1% to 3% comes from the fillets. Check the compactness of the flanges and the web, and the unbraced length of the beam, before using Mp as the strength. For weak-axis bending, use the formula of the weak axis, not this one.

The section modulus calculator covers the elastic modulus of other shapes, the moment of inertia calculator gives the second moment of area, the steel column capacity calculator checks compression members and the beam deflection calculator checks stiffness.

Frequently asked questions

What is the plastic moment?

When a steel beam is loaded in bending, the stress is linear across the section until the outer fibers yield, at the yield moment My. If the load increases, the yielded zone moves toward the center, and when the whole section has yielded, the beam reaches its plastic moment Mp and forms a plastic hinge. For a compact steel section Mp is the flexural strength used in the design standards, as in AISC 360.

What is the plastic section modulus?

The plastic section modulus Z is the sum of the first moments of the areas above and below the plastic neutral axis, the axis that divides the section in two equal areas. For a doubly symmetric shape this axis is the center line. The plastic moment is Mp = Fy Z. The elastic section modulus S = I / c gives the yield moment My = Fy S instead.

What does the shape factor tell?

The shape factor Z / S measures the reserve of strength after the first yield. It is 1.5 for a rectangle, about 1.10 to 1.15 for rolled I-shapes in strong-axis bending and about 1.7 for a solid circle. A high shape factor means that the section keeps a big reserve of strength, which plastic analysis uses to redistribute moments in continuous beams.

What are the limits of this calculator?

It applies to a doubly symmetric I-shape in bending about the strong axis, and it ignores the fillets of the web, which makes the values a little lower than the tables. The full plastic moment needs a compact section, in which the flanges and the web are thick enough to avoid local buckling, and a beam that is braced against lateral-torsional buckling. The design standard gives the reduced strength otherwise.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.