Skip to content
Omnikalc

Steel column capacity calculator: AISC buckling strength of a compression member

Enter the effective length, the radius of gyration, the area and the yield stress of a steel column to get the slenderness, the critical stress, the nominal strength and the LRFD and ASD design strengths.

Updated on
Your inputs

Value out of range

ft

Value out of range

in

Value out of range

in²

Value out of range

ksi

Value out of range

Results

Design strength φPn (LRFD, φ = 0.90)

283.3 kips

Slenderness ratio KL/r
71.3
Stocky or intermediate column
Elastic buckling stress Fe
56.3 ksi
Critical stress Fcr
34.5 ksi
Nominal strength Pn
314.8 kips
Allowable strength Pn / Ω (ASD, Ω = 1.67)
188.5 kips

The buckling strength of a steel column falls as it gets more slender. The steel column capacity calculator applies the AISC 360 equations to give the slenderness, the elastic buckling stress, the critical stress, the nominal strength and the LRFD and ASD design strengths of the column.

How the calculation works

  • Enter the effective length factor K (1.0 for a pinned column, 0.65 for fixed ends, 2.0 for a cantilever) and the unbraced length of the column.
  • Enter the radius of gyration r about the weak axis and the gross area A of the section, from the steel tables (for example 2.02 in and 9.13 in² for a W8×31).
  • Enter the yield stress Fy (50 ksi for A992 steel). The modulus is E = 29,000 ksi.
  • The calculator applies the flexural buckling equations of AISC 360 chapter E: Fe = π²E / (KL/r)², then Fcr = 0.658^(Fy/Fe) Fy for the inelastic range or 0.877 Fe for the elastic range.

Example

A W8×31 column (A = 9.13 in², r = 2.02 in about the weak axis) is 12 ft long, pinned, with K = 1.0 and Fy = 50 ksi. The slenderness is KL/r = 144 / 2.02 = 71.3. The Euler stress is Fe = π² × 29,000 / 71.3² = 56.3 ksi. Since Fy / Fe = 0.888 is below 2.25, Fcr = 0.658^0.888 × 50 = 34.5 ksi. The nominal strength is Pn = 34.5 × 9.13 = 314.8 kips. The design strength is φPn = 0.9 × 314.8 = 283.3 kips, and the allowable strength is 188.5 kips.

Why it matters

The calculator helps structural engineering students, designers and steel detailers to check the capacity of a column, to compare sections and lengths, and to see how the bracing changes the strength. It gives the hand calculation of the code in seconds.

Good to know

Use the weak axis radius of gyration unless the column is braced about it. Check the slenderness: above 200, the code recommends a different member. Remember that the strength falls fast when K or the length increases, since the stress goes with the inverse of the square of the slenderness. Add the bracing points to reduce the unbraced length.

The Euler buckling calculator gives the elastic critical load, the beam deflection calculator checks serviceability, the bolt shear capacity calculator sizes the connections and the rebar development length calculator covers reinforced concrete.

Frequently asked questions

How is the strength of a steel column computed?

AISC 360 gives the flexural buckling strength of a compression member as Pn = Fcr × Ag. The critical stress depends on the slenderness KL/r. The elastic buckling stress is Fe = π² E / (KL/r)². If KL/r is not more than 4.71 √(E/Fy), which is the same as Fy/Fe ≤ 2.25, the column buckles inelastically and Fcr = 0.658^(Fy/Fe) × Fy. Otherwise, it buckles elastically and Fcr = 0.877 Fe.

What are LRFD and ASD?

They are the two design methods of AISC. In LRFD, the design strength is φ Pn with φ = 0.90 for compression, and it must be at least the factored load Pu. In ASD, the allowable strength is Pn / Ω with Ω = 1.67, and it must be at least the service load Pa. Both give almost the same result for a typical live to dead load ratio. Use the one that your project and your code require.

Which axis and which K should I use?

A column buckles about the axis with the largest slenderness, which is usually the weak axis, with the smallest r. If the column is braced differently about the two axes, compute both and keep the lowest strength. K depends on the end conditions and on the sway of the frame. The values 0.65, 0.8, 1.0, 1.2, 2.0 and 2.1 are the theoretical and the recommended values for the ideal cases.

What does this calculator not include?

It covers the flexural buckling of doubly symmetric sections without slender elements. It does not include the torsional or flexural-torsional buckling of angles and tees, the local buckling of slender plates, the combined axial and bending effects or the connection design. For real structures, a licensed engineer must design the column according to the code.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.