Skip to content
Omnikalc

Rainfall intensity-duration-frequency curve calculator

Enter the three coefficients of the local IDF curve, the storm duration, the runoff coefficient and the area to get the intensity, the depth and the runoff volume.

Updated on
Your inputs

Value out of range

min

Value out of range

Value out of range

min

Value out of range

Value out of range

acres

Value out of range

Results

Rainfall intensity for the duration

3.59 in/h

Rainfall depth of the storm
1.79 in
Intensity for a 60-minute storm
2.31 in/h
Intensity to the 60-minute intensity
1.55
Runoff volume of the storm
1.256 acre-ft

The rainfall IDF curve calculator gives the rainfall intensity and the storm depth for a duration from the coefficients of a local curve, the ratio to the 60-minute intensity and the runoff volume of a drainage area.

How the calculation works

  • Enter the coefficients a, b and c of the local intensity-duration-frequency curve for the return period you design for.
  • Enter the storm duration, the runoff coefficient and the drainage area.
  • The calculator gives the rainfall intensity, the rainfall depth, the 60-minute intensity and the runoff volume.

Example

A local curve for a 10-year storm is i = 70 / (t + 11)^0.8, with i in in/h and t in minutes. For a 30-minute storm the intensity is 70 / 41^0.8 = 3.59 in/h and the depth is 1.79 in. A 60-minute storm has an intensity of 2.31 in/h, so the 30-minute storm is 1.55 times as intense. On a drainage area of 12 acres with a runoff coefficient of 0.70, the runoff volume of the storm is 1.256 acre-ft.

Why it matters

The calculator helps drainage engineers, site designers, students and permit reviewers to read an IDF curve quickly, to compare the intensity at several durations and to get a first estimate of the runoff volume for a basin or a retention requirement.

Good to know

Use the coefficients of the nearest official station and the return period required by your regulation, for example 2, 10 or 100 years. Check that the duration is within the range of the fit. Run the calculator at several durations to find the one that gives the largest volume for a basin, and the time of concentration for the intensity used in the rational method. Apply the safety factor or climate allowance of your jurisdiction.

The rational method calculator gives a peak flow from the intensity, the time of concentration calculator gives the duration to use, the Gumbel flood frequency calculator fits a flood record and the detention pond storage calculator sizes the basin.

Frequently asked questions

What is an IDF curve?

An intensity-duration-frequency curve gives the average rainfall intensity for a storm of a given duration and a given return period, such as 10 years. Short storms are intense and long storms are gentler, so the intensity falls as the duration grows. Cities and agencies publish the curves, or the coefficients of a formula, and they are the basis for sizing storm drains, culverts and detention basins.

What is the Sherman form of the curve?

A common form is i = a / (t + b)^c, where t is the duration in minutes, and a, b and c are fitted to the rainfall record of the place and the return period. The coefficients depend on the units, so use the values given for in/h or for mm/h. Another form is the Talbot equation i = a / (t + b), which is the same with c = 1. The calculator accepts any curve of this family.

How is the runoff volume found?

The depth of the storm is the intensity times the duration. The runoff depth is the depth times the runoff coefficient, which stands for the share of the rain that runs off, and the volume is this depth times the drainage area. This is a simple volume for a storm of uniform intensity and it gives a first value for a detention basin. For a hydrograph or a design of a basin, use a routing method.

What are the limits of the calculation?

The IDF curve gives an average intensity, not the real rainfall pattern in time, and its coefficients are valid only for the range of durations of the fit, often 5 minutes to 24 hours. The runoff coefficient is a constant that ignores the loss at the start of the storm and the wet state of the soil. For large areas, apply an area reduction factor and use a design storm and a hydrologic model.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.