Skip to content
Omnikalc

Roof heat cable length and power calculator for ice dams

Enter the length of the eave, the cable pattern, the gutter, the downspouts, the cable power and the voltage to get the length of cable, the power, the current and the number of circuits.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

W/ft

Value out of range

V

Value out of range

A

Value out of range

Results

Circuits required

1

Cable on the roof edge
150 ft
Total length of cable
234 ft
Power
1,404 W
Current
11.7 A

The roof heat cable calculator gives the length of cable on the roof edge, the total length with the gutter and the downspouts, the power, the current and the number of circuits of a de-icing system, from the length of the eave, the cable pattern, the power of the cable and the supply voltage.

How the calculation works

  • Enter the length of the eave and the cable per foot of eave in the zigzag pattern.
  • Enter the length of the gutter and of the downspouts to be heated, and the power of the cable.
  • Enter the voltage and the breaker to get the total length, the power, the current and the number of circuits.

Example

A roof edge of 60 ft with 2.5 ft of cable per foot of eave needs 150 ft of cable. With 60 ft of gutter and 24 ft of downspouts, the total is 234 ft. At 6 W/ft the power is 1,404 W, and on 120 V the current is 11.7 A. A 15 A breaker carries 12 A at 80 %, so the system needs 1 circuit.

Why it matters

The calculator helps electricians, roofers, homeowners and building managers to estimate the cable, the load and the circuits of a roof de-icing system, to compare the cost of the cable with the power used in winter, and to prepare the order before they ask for a quote.

Good to know

Treat the cause first: seal the air leaks to the attic, add insulation and ventilate the roof. Install the cable according to the manufacturer’s pattern, fix it with the clips made for the roof, and protect the circuit with a ground-fault breaker. Use a thermostat or a moisture sensor so that the cable works only when it is needed, and switch it off in the spring.

The heat tracing power calculator sizes the cable that keeps a pipe from freezing, the ice melt calculator gives the quantity of de-icing salt, the snow load calculator gives the snow on a roof and the roof scupper sizing calculator sizes the drains of a flat roof.

Frequently asked questions

What does a roof heat cable do?

A roof heat cable, or de-icing cable, is laid in a zigzag on the lower edge of a roof, and in the gutters and the downspouts. It keeps a channel open where the water from the melting snow can run off, so that it does not freeze at the eave and back up under the shingles. This stops the ice dam and the water leaks that it causes.

How much cable do I need?

The length depends on the overhang of the roof and on the height of the loops. A common layout uses about 2.5 to 3 ft of cable for each foot of eave, with loops that rise 18 to 24 in on the roof. Add the length of the gutter and of the downspouts, which are heated with a straight run of the cable. Use the layout chart of the cable manufacturer.

How many circuits are needed?

The power is the total length times the power per unit of length. The current is the power divided by the voltage. Electrical rules limit a continuous load to 80 % of the rating of the breaker, so a 15 A breaker carries 12 A. If the current is higher than this, the cable must be split on several circuits, or a breaker of a higher rating with the proper wire must be used.

What are the limits of the calculator?

The calculator does not give the heating of the attic, which is the real cause of most ice dams. The best cure is to seal the air leaks, to add insulation and to ventilate the attic. The cable treats the symptom. The calculator also does not include the controls, the ground fault protection or the maximum circuit length of the cable, which the installation guide gives.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.