Skip to content
Omnikalc

Radial ice load on a wire or cable with concurrent wind calculator

Enter the wire diameter, its weight, the radial ice thickness and the concurrent wind speed to get the ice weight, the wind load on the iced wire and the resultant load.

Updated on
Your inputs
in

Value out of range

lb/ft

Value out of range

in

Value out of range

mph

Value out of range

Value out of range

Results

Resultant load

2.897 lb/ft

Weight of the ice
1.702 lb/ft
Total vertical load
2.796 lb/ft
Wind load on the iced wire
0.757 lb/ft
Resultant to bare weight
2.65
A heavy ice load: check the supports and the tension

The radial ice load calculator gives the weight of the ice on a wire or cable, the vertical load, the concurrent wind load on the iced wire and the resultant load, with its ratio to the bare weight.

How the calculation works

  • Enter the diameter and the weight of the bare wire or cable.
  • Enter the radial thickness of ice and the concurrent wind speed.
  • The calculator gives the weight of the ice, the vertical load, the wind load on the iced wire and the resultant.

Example

A conductor 1.108 in in diameter weighs 1.094 lb/ft and carries 0.75 in of radial ice with a 40 mph concurrent wind. The ice weighs π × 56 × 0.75 × (1.108 + 0.75) / 144 = 1.702 lb/ft, so the vertical load is 2.796 lb/ft. The wind pressure is 0.00256 × 40² = 4.10 psf on the iced diameter of 2.608 in, which gives 0.757 lb/ft with a drag coefficient of 1.0 and a gust factor of 0.85. The resultant is 2.897 lb/ft, 2.65 times the bare weight.

Why it matters

The calculator helps line engineers, tower and mast designers, utility staff and students to see how much an ice storm adds to the load of a conductor, a cable or a guy, and to size the wire, the supports and the tension for that load.

Good to know

Use the ice thickness and the concurrent wind speed of the standard for the site, not a guess. Apply the load factors and check the structure for unbalanced ice too, when ice falls from one span. Include the ice on the supports, the insulators and the guys. For long spans, calculate the sag and the tension under the resultant load, and check the clearance to the ground.

The wire rope capacity calculator gives the strength of a rope, the guyed mast calculator gives the tension in the guys, the roof heat cable calculator sizes an ice dam heater and the wind cladding pressure calculator gives the wind pressure on a building.

Frequently asked questions

How is the weight of ice found?

Ice forms a uniform sleeve of radial thickness t around a wire of diameter D. Its cross-section is π t (D + t), and with a density of 56 lb/ft³ (900 kg/m³) the weight per foot is π × 56 × t (D + t) / 144 with the dimensions in inches. The weight grows with the square of the thickness, so doubling the ice thickness more than doubles the load. The ice thickness comes from the map or table of the standard for the region.

Why is there a concurrent wind?

Ice storms are often followed or accompanied by wind, and the iced wire has a larger diameter that catches more wind. The standards combine a design ice thickness with a reduced wind speed, because the full design wind and the full design ice rarely occur together. The wind pressure is 0.00256 V² in psf with V in mph and the load per foot is this pressure times the iced diameter, with a drag coefficient and a gust factor.

What does the resultant tell me?

The vertical load of the wire and the ice and the horizontal load of the wind are at right angles, so the resultant is the square root of the sum of their squares. It is the load that the wire, the insulators, the supports and the guys must carry, and it gives the tension and the sag of the span. The ratio to the bare weight shows how much heavier the wire becomes. Ratios of 2 to 4 are common in the heavy ice regions.

What are the limits of the calculation?

The calculation assumes a uniform ice sleeve of constant density around a round wire. Real ice can be uneven, can form as rime, glaze or wet snow with different densities, and can shed unevenly, which loads the supports with an unbalanced force. It also leaves out the dynamic effect of galloping. Use the ice thickness, the wind and the load factors of the standard of your project and a full line analysis for a design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.