Skip to content
Omnikalc

Rotameter flow calculator: correct the reading for the liquid density

Enter the reading of a variable area flow meter calibrated on water, the float density and the density of your liquid to get the actual flow rate, the correction factor and the mass flow rate.

Updated on
Your inputs
gpm

Value out of range

gpm

Value out of range

lb/ft³

Value out of range

lb/ft³

Value out of range

lb/ft³

Value out of range

Results

Actual flow rate of the liquid

5.48 gpm

Density correction factor
1.097
Reading as a share of the full scale
50.0 %
Reading in the accurate part of the scale
Mass flow rate
38.85 lb/min
Actual flow rate at full scale
10.97 gpm

A rotameter is a variable area flow meter whose scale is printed for water. The rotameter flow calculator corrects the reading for the density of the real liquid and the float, and gives the actual flow rate, the mass flow rate and the position on the scale.

How the calculation works

  • Enter the reading of the rotameter on its water scale and its full scale.
  • Enter the density of the float (about 500 lb/ft³ for stainless steel 316), the density of the calibration fluid (water, 62.4 lb/ft³) and the density of the real liquid.
  • The calculator applies the density correction CF = √[(ρf − ρ) ρc / ((ρf − ρc) ρ)] to the reading and gives the actual flow rate.
  • It also gives the mass flow rate, the position of the reading on the scale and the actual full-scale flow of the meter with this liquid.

Example

A stainless steel float of 500 lb/ft³ in a rotameter calibrated on water reads 5 gpm on a 10 gpm scale, but the liquid is an oil of 53 lb/ft³. The correction factor is √[(500 − 53) × 62.4 / ((500 − 62.4) × 53)] = 1.097. The actual flow rate is 5 × 1.097 = 5.48 gpm, or 38.85 lb/min. The reading is at 50% of the scale, in the accurate range, and the meter would read 10.97 gpm of this oil at full scale.

Why it matters

The calculator helps process operators, laboratory and pilot plant staff, water treatment technicians and students to read a rotameter correctly with a liquid that is not water, to avoid dosing errors, and to check whether the meter range fits the duty. It saves a trip to the manufacturer’s correction tables.

Good to know

Use the density of the liquid at the operating temperature. Make sure that the float material is the one that the meter was calibrated with. Do not trust the reading below 10% of the scale. Use the manufacturer’s sizing software for viscous liquids, gases and slurries, which this simple correction does not cover.

The orifice flow calculator gives the flow from a pressure drop, the Reynolds number calculator checks the flow regime, the pump power calculator sizes the pump and the tank volume calculator gives the volume of the vessel.

Frequently asked questions

How does a rotameter work?

A rotameter is a vertical tapered tube with a float inside. The fluid flows up and lifts the float until the gap around it is big enough for the force of the flow to balance the weight of the float in the fluid. The higher the float, the larger the flow. The scale is read at the top edge of the float. The meter is simple, cheap, has no need for power and gives a direct view of the flow.

Why must the reading be corrected for the liquid?

The scale is printed for the calibration fluid, usually water at room temperature. For a liquid of another density, the buoyancy of the float changes, so the same float height corresponds to another flow rate. A lighter liquid gives a higher flow for the same reading. The correction depends on the density of the float, which is why a manufacturer gives the float material with the meter.

Does the viscosity matter?

The correction here is for density only and is valid when the meter is viscosity-immune, which is the case for a float designed for it and for liquids with a viscosity under about 10 cP. Above that, the flow coefficient changes and the manufacturer’s viscosity correction must be applied. For gases, the correction uses the pressure and the temperature and a different formula.

What is the best part of the scale?

A rotameter is usually accurate within 2 to 5% of full scale, which means that its error in percent of the reading becomes large at a low reading. For best results, choose the meter so that the normal flow is between 30 and 70% of the scale. The calculator warns below 10% and above 90%, where the accuracy is poor or the float may hit the stop.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.