Skip to content
Omnikalc

Seismic story drift and stability coefficient calculator

Enter the story load, drift, shear, height and Cd to get the ASCE 7 stability coefficient, its maximum, the P-delta amplification and the story drift check.

Updated on
Your inputs
kips

Value out of range

in

Value out of range

kips

Value out of range

ft

Value out of range

Value out of range

Value out of range

Value out of range

Results

Stability coefficient θ

0.103

Maximum stability coefficient θmax
0.111
Ratio θ to θmax
0.92
The stability coefficient is within the maximum value
P-delta amplification 1 / (1 − θ)
1.114
Story drift ratio
1.28 %
Drift to allowable ratio
0.51
The story drift is within the allowable value

The seismic story drift calculator gives the stability coefficient θ of ASCE 7, its maximum value, the P-delta amplification factor, the story drift ratio and the check against the allowable drift of the risk category.

How the calculation works

  • Enter the vertical load at and above the story, the design story drift, the seismic shear and the story height.
  • Enter Cd, the importance factor, β and the allowable drift of the risk category.
  • The calculator gives the stability coefficient θ, its maximum, the P-delta amplification and the drift checks.

Example

A story 13 ft high (156 in) carries 9,000 kips at and above its level, with a seismic shear of 250 kips and a design story drift of 2.00 in, in a system with Cd = 4.5 and Ie = 1.0. The stability coefficient is θ = 9,000 × 2.00 × 1.0 / (250 × 156 × 4.5) = 0.103. The maximum is 0.5 / (1.0 × 4.5) = 0.111, so the ratio is 0.92. The amplification is 1 / (1 − 0.103) = 1.114. The drift is 2.00 / 156 = 1.28 %, against 2.5 % allowed, a ratio of 0.51.

Why it matters

The calculator helps structural engineers, plan checkers and students to check the second-order effects and the drift of a story after the seismic analysis, and to see how the vertical load, the shear and the stiffness change the stability.

Good to know

Use the design story drift Δ that includes Cd / Ie, not the elastic drift, and the total vertical load of the load combination of the code, which is lower than the full dead plus live load in a seismic combination. Check every story, since the lowest stories carry the most load and usually govern. If θ is over 0.10 in a story, add the amplification to the member forces of that story and the stories below.

The shear wall calculator gives the unit shear and the hold-down force, the wind load calculator gives the lateral load of the wind, the live load reduction calculator gives the reduced live load of a column and the tuned mass damper calculator sizes a damper for a flexible structure.

Frequently asked questions

What is the stability coefficient?

The stability coefficient θ in ASCE 7 section 12.8.7 is θ = Px Δ Ie / (Vx hsx Cd), where Px is the total vertical load at and above the story, Δ the design story drift, Vx the seismic shear of the story, hsx the story height and Cd the deflection amplification factor. It is the ratio of the second-order overturning moment from the gravity load acting on the drift to the first-order moment of the seismic shear.

When must the P-delta effects be included?

If θ is 0.10 or less, the P-delta effects may be ignored. If θ is over 0.10, the story drifts and forces must be multiplied by 1 / (1 − θ), or computed in a second-order analysis. In all cases θ must not exceed θmax = 0.5 / (β Cd), and not more than 0.25. A story over θmax is potentially unstable and the structure must be stiffened or re-designed. β is the ratio of the shear demand to the shear capacity, and 1.0 is conservative.

What drift limits apply?

ASCE 7 Table 12.12-1 sets the allowable story drift for the structures that are not masonry or special types, at 0.025 hsx for Risk Category I and II, 0.020 hsx for Category III and 0.015 hsx for Category IV. The limits are for the design story drift Δ, which already includes the factor Cd / Ie. Other structure types, such as some masonry walls, have lower limits, and the limits can be different in a code that you work to.

What does the calculator leave out?

The calculator checks one story at a time from the values that you enter. It does not run the structural analysis, the torsional amplification, the redundancy, the story-to-story drift difference at the two ends of a diaphragm or the effect of a deformation-compatibility check. The metric version uses the same American equations and only changes the units, and a code such as Eurocode 8 uses its own coefficient θ and limits.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.