Skip to content
Omnikalc

Live load reduction calculator: reduced floor live load for columns and beams

Enter the live load, the tributary area, the element factor KLL, the number of floors and the dead load to get KLL × AT, the reduction factor, the reduced live load, the reduction and the total load on the member.

Updated on
Your inputs
psf

Value out of range

ft²

Value out of range

psf

Value out of range

Results

Reduced live load

25.8 psf

KLL × tributary area
3,200 ft²
Live load reduction factor
0.515
Reduction of the live load
48.5 %
Total unfactored load on the member
68.6 kips

The live load reduction calculator gives KLL × AT, the reduction factor, the reduced live load, the percentage of reduction and the total load on a column or a beam, from the ASCE 7 equation, the element factor KLL and the tributary area.

How the calculation works

  • Enter the unreduced live load of the occupancy, the tributary area of the member and the dead load.
  • Choose the element factor KLL, which depends on the type of member, and the number of floors supported by the member.
  • The calculator finds KLL × AT, the reduction factor of ASCE 7, the reduced live load, the percentage of reduction and the total unfactored load on the member.

Example

An interior column (KLL = 4) of a floor with a live load of 50 psf has a tributary area of 800 ft² and carries one floor. KLL × AT = 3,200 ft², above the threshold of 400 ft². The factor is 0.25 + 15 / √3,200 = 0.515, so the reduced live load is 50 × 0.515 = 25.8 psf, a reduction of 48.5 %. With a dead load of 60 psf, the total load is (60 + 25.76) × 800 / 1000 = 68.6 kips.

Why it matters

The calculator helps structural engineers, designers and students to estimate the live load on columns, girders and footings with the reduction of the code, to see how the tributary area and the number of floors change the load, and to check a hand calculation.

Good to know

Use the tributary area of the real member and the correct KLL factor from the table. Do not reduce the loads that the code excludes, and apply the reduction before the load combinations. For the columns of many floors, accumulate the tributary area of all the floors.

The load combinations calculator gives the factored loads, the steel column capacity calculator checks the column, the beam deflection calculator checks the beam and the roof snow load calculator gives the load on the roof.

Frequently asked questions

Why can the live load be reduced?

It is not probable that the full live load acts on a large area of floor at the same time. So the building codes allow a reduction of the live load on members that support a large area, such as columns, girders and the foundations. The reduction depends on the influence area of the member, which is the product of the element factor KLL and the tributary area AT.

What is the ASCE 7 equation?

In section 4.7, the reduced live load is L = L0 (0.25 + 15 / √(KLL AT)) in US units, or L = L0 (0.25 + 4.57 / √(KLL AT)) in SI units, with AT in square meters. The reduced load cannot be less than 0.50 L0 for members that support one floor, and 0.40 L0 for members that support two floors or more. The reduction is only allowed if KLL AT is 400 ft² (37.2 m²) or more.

What are the exceptions?

The reduction is not permitted for the live loads of more than 100 psf (4.8 kPa) in general, except for the members that support two floors or more where it is allowed with a limit, and for the places of public assembly. It is also not permitted for the passenger vehicle garages, except for the members that support two floors or more, with a reduction up to 20 %. The roof live load has its own reduction rules.

What are the limits of the calculator?

The calculator applies the basic equation. It does not apply the special rules for the heavy live loads, the garages, the public assembly, the roofs or the one-way slabs with a tributary area of 400 ft² and more, and the local building code can differ from ASCE 7. The loads must be taken from the building code and the structure designed by a qualified engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.