Skip to content
Omnikalc

Slab on grade calculator: stress in a concrete floor under a wheel load

Enter the wheel load, the contact radius, the thickness, the concrete properties and the subgrade modulus to get the interior and edge stresses, the allowable stress and the ratio.

Updated on
Your inputs
lb

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

pci

Value out of range

psi

Value out of range

Value out of range

Results

Edge stress under the wheel

179 psi

Radius of relative stiffness
28.9 in
Interior stress under the wheel
117 psi
Allowable tensile stress
237 psi
Ratio of the edge stress to the allowable
0.76
The slab is thick enough for the wheel load

The slab on grade calculator gives the radius of relative stiffness, the interior stress, the edge stress, the allowable tensile stress and the ratio of a concrete slab under a wheel load, with the Westergaard formulas, from the load, the thickness, the concrete and the modulus of subgrade reaction.

How the calculation works

  • Enter the wheel load, the radius of the contact area of the tire and the thickness of the slab.
  • Enter the modulus of elasticity and the strength of the concrete, the modulus of subgrade reaction and the factor of safety.
  • The calculator finds the radius of relative stiffness, the interior and edge stresses of Westergaard, the allowable stress and the ratio.

Example

A wheel of 4,000 lb with a contact radius of 4 in loads a slab of 7 in with E = 3,600,000 psi and k = 150 pci. The radius of relative stiffness is (3.6 × 10⁶ × 7³ / (12 × 0.9775 × 150))^0.25 = 28.9 in, and the equivalent radius b is √(1.6 × 4² + 7²) − 0.675 × 7 = 3.91 in. The interior stress is 117 psi and the edge stress is 179 psi. The allowable stress is 7.5 × √4,000 / 2 = 237 psi, so the ratio is 0.76.

Why it matters

The calculator helps floor and pavement designers, warehouse planners, contractors and students to check the thickness of a slab for a forklift or a truck wheel, to compare the effect of the thickness and of the subgrade support, and to understand why the edge of the slab governs.

Good to know

Use a subgrade modulus from a plate load test or a reliable correlation, and a compacted base to make the support uniform. Check the edge and the corner loads at the joints, where the stress is the highest, and use the dowels to share the load. Choose the thickness with a margin, because the extra thickness is cheap compared with the cracking of a floor in service.

The slab joint spacing calculator gives the spacing of the joints, the CBR subgrade modulus calculator estimates the modulus of the subgrade, the one-way slab minimum thickness calculator handles the suspended slabs and the punching shear calculator checks the concentrated loads.

Frequently asked questions

What is the Westergaard analysis?

Westergaard studied a concrete slab on a spring-like subgrade, called the Winkler foundation, and found the stress at the bottom of the slab under a wheel load. The interior stress is for a load far from the edges and the edge stress is for a load at the free edge of the slab, which is higher. The formulas depend on the load, the thickness, the radius of the contact area and the radius of relative stiffness of the slab.

What is the radius of relative stiffness?

The radius of relative stiffness is a length that measures the stiffness of the slab compared with the support of the subgrade. It is the fourth root of the modulus of elasticity of the concrete times the cube of the thickness, divided by 12 times (1 − ν²) times the modulus of subgrade reaction, with a Poisson ratio ν of 0.15 for concrete. A thicker slab or a softer subgrade gives a longer radius, and the load spreads over a larger area.

How is the allowable stress chosen?

The allowable tensile stress is the modulus of rupture of the concrete, estimated as 7.5 times the square root of the compressive strength in psi, divided by a factor of safety. A factor of 2 or more is used for the many repetitions of the load, to avoid the fatigue cracking. For the industrial floors, the factor of safety is chosen with the load type and the number of passes of the vehicles.

What are the limits of the calculator?

The calculator uses the classic Westergaard formulas for a single wheel and does not include the multiple wheels, the loads near a corner or a joint, the thermal curling, the shrinkage, the load transfer through the joints or dowels, the fatigue analysis or the racking loads. The modulus of the subgrade reaction must come from a plate test or a correlation. For a heavy floor, use the method of the PCA or of the ACI 360.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.