Skip to content
Omnikalc

Spherical dome membrane forces and ring tension calculator

Enter the radius, the opening angle, the thickness and the surface load of a spherical dome to get the meridional and hoop forces, the tension in the base ring and the steel area of the ring.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

in

Value out of range

psf

Value out of range

ksi

Value out of range

Results

Tension in the base ring

70.3 kips

Meridional force at the crown
2.10 kip/ft
Meridional force at the base
2.38 kip/ft
Hoop force at the base (tension positive)
-0.84 kip/ft
The hoop force at the base is compression
Ring steel required
1.30 in²
Meridional stress at the base
49.5 psi

The spherical dome calculator applies the membrane theory to give the meridional and hoop forces of a dome under a uniform surface load, the tension in the base ring and the steel it needs.

How the calculation works

  • Enter the radius of the sphere, the half opening angle at the base and the thickness of the shell.
  • Enter the load per unit of surface, which includes the self weight of the shell, and the steel strength of the ring.
  • The calculator gives the meridional force at the crown and at the base, the hoop force at the base, the tension in the ring beam and its steel.

Example

A dome with a radius of 60 ft, a half opening angle of 40° and a thickness of 4 in carries 70 psf of surface load. At the crown the meridional force is wa / 2 = 2.10 kip/ft. At the base it is wa / (1 + cos 40°) = 4,200 / 1.766 = 2.38 kip/ft, a stress of 49.5 psi. The hoop force at the base is wa (1 / (1 + cos φ) − cos φ) = -0.84 kip/ft, a compression. The base ring resists the outward thrust of the dome, which gives a tension of 70.3 kips, or 1.30 in² of Grade 60 steel at φ = 0.9. For an opening angle of 70°, the base hoop force turns to tension at 1.69 kip/ft.

Why it matters

The calculator helps structural engineers, architects of domes and silos, and students to size a thin concrete or masonry dome and its ring beam, and to see how the opening angle changes the forces. It also shows why a dome that is deeper than about 52 degrees needs hoop steel.

Good to know

Express the load per unit of surface of the shell, not per unit of plan, which changes with the angle. For a snow load, which acts on the plan, convert it by dividing by the factor that comes from the dome shape. The membrane results are accurate away from the edges only, so expect local bending near the ring. Detail the ring so that it can expand freely or is stiff enough, and keep the shell thick enough to avoid buckling, which for a concrete dome is typically 3 to 4 in per 60 ft of span.

The spherical cap calculator gives the area and the volume of the dome, the cable sag calculator handles a hanging cable, the three-hinged arch calculator gives a similar horizontal thrust and the pressure vessel stress calculator treats the membrane stress of a pressurized shell.

Frequently asked questions

What is the membrane theory of a dome?

A thin shell of revolution can carry a surface load by forces in its own plane only, with no bending, if its edges are free to follow the deformation. For a spherical dome under a uniform load w on the surface, the meridional force is Nφ = −w a / (1 + cos φ), in compression, and the hoop force is Nθ = −w a (cos φ − 1 / (1 + cos φ)). The calculator gives these at the crown and at the base.

When does the hoop force turn to tension?

The hoop force is compression near the crown, then falls to zero at the angle where cos φ equals 1 / (1 + cos φ). That angle is about 51.8 degrees from the vertical. Past it, the hoop force is tension, and the shell needs hoop reinforcement or a prestressing. A dome of a half angle below 51.8 degrees keeps its hoop forces in compression, as the calculator shows.

Why is there a ring at the base?

At the base, the meridional force has a horizontal part that pushes outward, much as an arch pushes on its abutments. A ring beam resists that thrust in tension, as a barrel hoop does. The tension in the ring is T = w a² sin φ cos φ / (1 + cos φ), and the ring steel is that force divided by the design strength. The ring must be continuous and well anchored, or the dome will spread.

What does the calculator leave out?

The calculator leaves out the bending near the edges, where the ring and the shell do not deform the same way, the wind and the snow loads that are not symmetric, the buckling of a thin dome, the openings, and the creep of concrete. It takes a load per unit of surface, so the self weight must be included. For a thick or shallow dome, a full analysis is needed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.