Skip to content
Omnikalc

Three-hinged arch reactions and horizontal thrust calculator

Enter the span, the rise, a uniform load and a point load to get the vertical reactions, the horizontal thrust, the total reactions and the bending moment of a three-hinged parabolic arch.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

kip/ft

Value out of range

kips

Value out of range

ft

Value out of range

Results

Horizontal thrust

46.0 kips

Vertical reaction at the left support
51.0 kips
Vertical reaction at the right support
41.0 kips
Total reaction at the left support
68.7 kips
Total reaction at the right support
61.6 kips
Bending moment in the arch under the point load
112.5 kip-ft

The three-hinged arch calculator gives the vertical reactions, the horizontal thrust, the total reactions at the supports and the bending moment under a point load of a three-hinged parabolic arch with a uniform load.

How the calculation works

  • Enter the span and the rise of the arch at the crown hinge.
  • Enter the uniform load over the span and a point load with its distance from the left support.
  • The calculator gives the vertical reactions, the horizontal thrust, the total reactions and the bending moment under the point load.

Example

A three-hinged parabolic arch spans 60 ft with a rise of 15 ft. It carries 1.2 kip/ft over the whole span and a point load of 20 kips at 15 ft from the left support. The vertical reactions are 51.0 kips and 41.0 kips. The moment of the loads about the crown hinge is 690.0 kip-ft, so the thrust is 690.0 / 15 = 46.0 kips. The total reaction at the left is 68.7 kips. Under the point load the beam moment is 630.0 kip-ft, the arch height there 11.25 ft, and the arch moment 112.5 kip-ft.

Why it matters

The calculator helps structural engineers, students and designers of arch bridges, bridges and timber or steel arches to find the forces on the foundations, to see how the rise changes the thrust and to design the tie or the abutments.

Good to know

The rise is measured from the line of the supports to the crown hinge, and a flatter arch has a larger thrust because the thrust is inversely proportional to the rise. A tie between the supports takes the thrust and leaves only the vertical reactions on the foundation. Check that the point load lies between the supports and use the dimensions of the axis of the arch. For a load on only half of the span, a second case is needed. Always design the abutment for the larger thrust of the load cases, and design the arch section for the bending moment with the axial force.

The beam deflection calculator gives deflections of a straight beam, the masonry lintel calculator gives the load on an opening, the cable sag calculator gives the tension of a cable and the roof truss calculator gives the framing of a truss.

Frequently asked questions

Why is a three-hinged arch statically determinate?

An arch with two pinned supports has four reactions, two at each support, and only three equations of equilibrium. The third hinge at the crown adds a condition, that the bending moment there is zero, and that is the fourth equation. The reactions can then be found by statics alone, without regard to the stiffness of the arch.

How is the horizontal thrust found?

The vertical reactions come from the moment equilibrium about each support, like a simple beam. The thrust comes from the crown hinge: the moment of all the forces on one side of the hinge about the hinge is zero, so the thrust times the rise equals the moment that a simple beam of the same span would have at the midspan.

Why is the moment small in a parabolic arch?

A parabolic arch under a uniform load over the whole span has the funicular shape: the line of thrust coincides with the axis of the arch, so the bending moment is zero everywhere and the arch carries the load by compression only. A point load or a partial load moves the line of thrust away from the axis and produces bending.

What does the calculator leave out?

The calculator leaves out the self-weight that varies along the arch, a load on part of the span, temperature, the settlement of the supports and the shape other than parabolic. The point load must be inside the span. The thrust is the force to be taken by the foundation or by a tie between the supports.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.