Skip to content
Omnikalc

Spur gear contact ratio calculator

Enter the teeth of the pinion and the gear, the module, the pressure angle and the addendum to get the contact ratio, the length of action and the double-contact share.

Updated on
Your inputs

Value out of range

Value out of range

mm

Value out of range

°

Value out of range

Value out of range

Results

Contact ratio

1.635

Length of action
9.65 mm
Base pitch
5.904 mm
Share of the time with two pairs in contact
63.5 %
Share of the time with one pair in contact
36.5 %
Center distance
60.00 mm

The gear contact ratio calculator gives the contact ratio, the length of action, the base pitch, the share of the time with two pairs of teeth in contact, the share with one pair and the center distance of a pair of spur gears.

How the calculation works

  • Enter the teeth of the pinion and of the gear, and the module.
  • Enter the pressure angle and the addendum coefficient, which is 1 for a standard tooth.
  • The calculator finds the length of action on the line of contact and divides it by the base pitch.

Example

A pinion of 20 teeth and a gear of 40 teeth with a module of 2 mm, at a center distance of 60.00 mm, have a length of action of 9.65 mm and a base pitch of 5.904 mm. The contact ratio is 1.635: two pairs share the load 63.5 % of the time and a single pair carries it 36.5 %.

Why it matters

The calculator helps gear designers, mechanical engineers, students and makers who need smooth and quiet gears, and who want to check that a standard gear pair has enough overlap.

Good to know

Standard full-depth teeth with a 20 degree pressure angle give a ratio of 1.4 to 1.9 for common tooth numbers. Check the result for the smallest pinion of your range, because a pinion with few teeth has the lowest ratio, and undercut also appears under 17 teeth. Increase the ratio with more teeth, finer teeth of a smaller module, or helical teeth. The load is carried by one pair at the moments of single contact, so check the tooth bending stress for that case. A ratio near a whole number gives a more regular stiffness and less noise.

The spur gear calculator gives the pitch diameters and the center distance, the gear ratio calculator handles the speed, the planetary gear calculator uses gears on a common axis and the rack and pinion calculator treats a pinion with an infinite gear.

Frequently asked questions

What is the contact ratio of gears?

The contact ratio is the average number of tooth pairs in contact at the same time. It is the length of action along the line of contact divided by the base pitch. A ratio of 1.6 means that one pair is in contact for 40 % of the time and two pairs for 60 %. For smooth, quiet operation, the ratio should be above 1.2, and ideally 1.4 or more.

How is it calculated for spur gears?

The length of action is √(ra1² − rb1²) + √(ra2² − rb2²) − a × sin α, where ra is the outside radius, rb the base radius and a the center distance. The base pitch is π × m × cos α. For a 20-tooth pinion and a 40-tooth gear of module 2 and 20 degrees, the result is 1.635.

What increases the contact ratio?

More teeth, a larger addendum and a smaller pressure angle increase the contact ratio. A 14.5 degree angle gives more overlap than 25 degrees but weaker teeth. Helical gears add an overlap in the axial direction, so their total ratio is higher and they run more smoothly than spur gears.

What happens if the contact ratio is below 1?

A ratio under 1 means that there are moments when no pair is in contact, so the drive hits and the load is not carried continuously. Real designs keep the ratio at 1.2 at least. A drop under this value results from too few teeth or a too small addendum, and also from a center distance that is too large.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.